Oce TDS100 Скачать руководство пользователя

Страница: 41 / 70

Maintain the Océ TDS100

Clear an original jam

Introduction

The media jam indicator blinks and the message code 'E 0' displays to indicate
that an original jam occured. The type of original determines how to clear the
original jam. The types of originals are divided into the following.

■

Fragile originals

■

Normal originals.

When to do

You need to clear an original jam in the following situations.

■

The original is jammed

■

The media feed stopped during the copy job

■

The red stop key was pushed during a copy job.

How to remove a fragile original

Pull the top cover towards you and lift the top cover to open it.

[17] Open the top cover

Remove the original

Lower and push the top cover backwards until you hear or feel a click

Check on a media jam also and clear the media jam if necessary.
(see ‘Clear a media jam’ on page 43)

How to remove a normal original

Pull the original carefully with two hands toward you

Check on a media jam also and clear the media jam if necessary.
(see ‘Clear a media jam’ on page 43)

Содержание TDS100







































































Результаты поиска

Содержание TDS100

Отзывы:

Похожие инструкции для TDS100

Бренды по названию

Популярные бренды

Oce TDS100, Руководство пользователя

Результаты поиска

Содержание TDS100

Отзывы:

Похожие инструкции для TDS100

Бренды по названию

Популярные бренды