Oce TDS100 Скачать руководство пользователя | Manualshive

Страница: 38 / 70

background image

38

User manual

Add toner

Introduction

The Océ TDS100 illuminates the toner low indicator when the toner level is
low.

When the toner low indicator illuminates, you need to do the following.

■

Add toner

■

Replace the waste toner bag.

Note:

If you ignore the toner low indicator, the copy quality will decrease.

When to do

Add toner and replace the waste toner bag when the toner low indicator
illuminates. You can finish your copy job before you add the toner and replace
the waste toner bag.

Before you begin

Shake the toner bottle thoroughly.

Attention:

Use TDS100 toner only.

How to add toner and replace the waste toner bag

1.

Loosen the nut at the left back side.
Open the left cover.

[13] Open the left cover

[13] Open the left cover

1

2

«
...
36
37
38
39
40
...
»

Содержание TDS100







































































Отзывы:

Нет отзывов

Похожие инструкции для TDS100

Бренд: Sitecom Страницы: 9

Бренд: Xerox Страницы: 653

Бренд: Canon Страницы: 207

Бренд: Panasonic Страницы: 105

Бренд: Panasonic Страницы: 187

Бренд: Fuji Xerox Страницы: 3

Бренд: Fuji Xerox Страницы: 14

Document Centre 505

Бренд: Fuji Xerox Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды