Oce Repro Desk Скачать руководство пользователя страница 25

Страница: 25 / 464

Installation

Install Océ Repro Desk Server

Note:

Installation of the Server software is normally done by Service.

System requirements

The critical hardware components of the recommended hardware
configuration needed to run Océ Repro Desk Server 1.0 are:

■

700 MHz Pentium III processor or better

■

Minimum of 256 MB RAM

■

Minimum of 200 MB free hard disk space

■

A video card supporting a minimum resolution of 1024 x 768 at 24-bit color

■

Backup system

■

Anti-virus software

■

A 17-inch monitor

■

For TDS series machines, a dedicated 100 Mb/s network connection to
connect to the Power Logic Controller

Océ Repro Desk Server furthermore requires the installation of:

■

Windows 2000 (Pro or Server) or Windows XP Professional

■

Internet Explorer 5.0 or higher, with 5.5 or higher recommended

Preparation

Prior to installing the software, be sure to have the CD key available as well as
the Authorization code that enables the print capability.

■

Read and follow the instructions on the Welcome screen.

■

Carefully read the Software Licence Agreement screen.

▼

Install Océ Repro Desk Server

Place the CD in the CD-ROM drive.

Select a language.

Click ‘OK’.

Click on ‘Install’.
A message appears ‘Setup will now determine your system configuration’.

Содержание Repro Desk

















































































































































































































































































































































































































































































Результаты поиска

Содержание Repro Desk

Отзывы:

Oce Repro Desk, Руководство пользователя, Страница: 25 / 464

Результаты поиска

Содержание Repro Desk

Отзывы: