21
- GB -
Pos: 112 /Alle Produkte/Überschriften/H1 Installation @ 7\mod_1196624877149_121.doc @ 41391
5. Installation
Pos: 113 /Pumpen/Schlammsauger/Jumping Jet Rainbow Star/INS Aufstellen @ 7\mod_1196626077860_121.doc @ 41573
Installation (Fig. B, C):
Carefully plan the installation of the Jumping Jet Rainbow Star. Careful planning and taking the envi-
ronmental conditions into account will lead to optimum operating conditions for the Jumping Jet Rainbow
Star. The following points can help you with your planning.
►
Position the Jumping Jet Rainbow Star
(1)
and the 12V Master control box
(5)
at a sufficient dis-
tance from each other.
►
Keep a minimum distance to the water for the installation of the 12V Master control box
(5)
. For the
prescribed distances, please refer to the regulations for installers of electrical installations in/at gar-
den ponds valid in your country.
►
When laying cables
(19/20)
, please note the maximum cable lengths. Use the cable clips
(13)
to en-
sure proper routing of the two connection cables of the Jumping Jet Rainbow Star.
►
Position the Jumping Jet Rainbow Star
(1)
in a wind protected place. Risk of the water jet being bro-
ken apart by wind.
►
Where the water jet hits the water surface, the water depth must be at least 300 mm to avoid heavy
water splashes.
►
This point should not be too close to the basin rim (> 1 m). Never guide the water jet beyond the ba-
sin rim, as in this case splash water cannot be avoided.
►
Take the installation of another Jumping Jet Rainbow Star
(1)
(Jumping Jet Rainbow Star Add-On
set) into account that you might want to install in the future.
►
Place the pump
(21)
at a higher level to prevent drawing in of dirt particles from the bottom of the
basin. This increases the cleaning interval for the Jumping Jet Rainbow Star
(1)
.
►
Note the required water depth for the Jumping Jet Rainbow Star
(Fig. C)
.
Pos: 114 /Alle Produkte/Dummy_module/Abstand 6 pt @ 7\mod_1196627997106_0.doc @ 41651
Pos: 115 /Pumpen/Schlammsauger/Jumping Jet Rainbow Star/INS Jumping Jet montieren @ 7\mod_1196626170939_121.doc @ 41599
Installation of the Jumping Jet Rainbow Star (Fig. D, E)
Install the Jumping Jet Rainbow Star level and free from vibrations on a sturdy platform.
1. Fasten the unit foot
(23)
on the platform using 3 screws
(22)
(not included in our scope of delivery).
Turn the unit to the desired position and tighten the screws
(22)
.
2. Connect the hose
(2) (Fig. E)
In the case of steep inclination angles of the Jumping Jet Rainbow Star
(1),
the stepped hose
adapter
(15)
with socket
(16)
can be directly screwed onto the inlet
(24)
.
In the case of flat inclination angles, screw the two angle pieces
(17)
on the inlet
(24)
to be able to fit
the stepped hose adapter
(15)
including the socket
(16)
.
3. Slide the hose clip
(14)
over the hose
(2)
, plug the hose
(2)
on the stepped hose adapter
(15)
, and
secure by means of the hose clip
(14)
.
4. Connect the other hose end to the pump. Adhere to the information given in the pump operating in-
structions.
5. Where two Jumping Jet Rainbow Stars
(1)
are used, connect each hose end to the Y distribu-
tor
(Fig. B, 3)
and use hose
(2)
to connect the Y distributor to the pump. The Y distributor is part of
the delivery of the Jumping Jet Rainbow Star Add-On set.
Pos: 116 /Alle Produkte/Dummy_module/===== Seitenwechsel ===== @ 0\mod_1125648978015_0.doc @ 1631