OAK SCSI 4 Скачать руководство пользователя страница 3

Страница: 3 / 54

Neither the whole nor any part of the information contained in or the products described in this

manual may be adapted or reproduced in any material form without the prior written
permission of Shawbury Computers Limited (Oak).

The products described in this manual are subject to continuous development and

improvement. All information of a technical nature and particulars of the products and their

uses are given in good faith. However, it is acknowledged that there may be errors or

omissions in this manual.

All correspondence should be addressed to:

Customer Support (SCSI)
Oak
Cross Park House
Low Green
Rawdon
Leeds
LS19 6HA

All maintenance and service on the products described in this manual must be carried out by

Oak or their authorised agent. Oak can accept no liability for loss or damage whatsoever
arising from the use of any information or particulars in, or any error or omission in this
manual.

No responsibility is accepted for the installation of the Hard Disc and podule, or for any

consequential damage which results from incorrect use.

Oak is a trademark of Shawbury Computers Limited.

Archimedes, Risc OS and R140 are trademarks of Acorn Computers Limited.

All other trademarks acknowledged.

Issue 1.3

0 Copyright Oak 1989/1990

Содержание SCSI 4























































Результаты поиска

Содержание SCSI 4

Отзывы:

Похожие инструкции для SCSI 4

Бренды по названию

Популярные бренды

OAK SCSI 4, Руководство пользователя

Результаты поиска

Содержание SCSI 4

Отзывы:

Похожие инструкции для SCSI 4

Бренды по названию

Популярные бренды