O-Two 01EVE700 Скачать руководство пользователя страница 18

Страница: 18 / 60

e700 User Manual

3.5.2. Live Monitoring Parameters

The following Live Monitoring Parameters are displayed at the

section 2 of the screen:

Paw

(cmH

O):

Paw AV is the average patient airway pressure

measured during the last 60 seconds. This measurement is

monitored by the ventilator at all times and modes. The number on

the display will be updated every 15 seconds.

Mve (L):

Minute volume is the total exhaled volume for the last

60 seconds as calculated using the last 8 breaths. The Mve will

constantly change as the value is recalculated and displayed at the

end of exhalation phase. When unit is fi rst turned on or resumed

after pause or on selecting a new mode, the Mve calculation will

be based on fi rst then second then third and so on until the 8th

exhaled tidal volume when the above logic will be followed.

Rate (bpm):

Rate (BPM) is the rate at which breaths are delivered in

one minute. It is the monitored breath rate calculated by measuring

the time interval (Tb in seconds) between 2 breaths. Rate (BPM)

= 60 / Tb. The number is updated after each breath. This number

will be displayed for both mandatory and spontaneous breathing

phases.

Vte (ml):

Tidal volume is the volume exhaled from the patient in

mandatory, spontaneous or PSV (Pressure Support Ventilation)

breaths. Vte is calculated by the measurement of the entire expired

fl ow displayed as a volume. Vte display will be updated at the

beginning of the next inspiratory phase (The end of exhalation

phase).

Paw

Peak

(cmH

O):

Peak air way pressure is the maximum pressure

measured during the inspiratory phase. The displayed number on

the screen represents the maximum pressure during mandatory

inspiratory phase of A/CV, SIMV, BiLVL, CPR modes as well as

spontaneous inspiratory phase of CPAP mode. This number will be

updated at the end of each inspiratory phase.

Note:

Mve, Rate and Paw are not active during CPR mode and

displayed with “--“

Содержание 01EVE700





























































Результаты поиска

Содержание 01EVE700

Отзывы:

O-Two 01EVE700, Руководство пользователя, Страница: 18 / 60

Результаты поиска

Содержание 01EVE700

Отзывы: