NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 56

Страница: 56 / 68

Push the power button on the front side of the chassis. The board will boot and show the
U-Boot console messages, similar to the following.

U-Boot 2014.01QorIQ-SDK-T1040-BSP0.2 (Mar 07 2014 - 01:04:58)

CPU0: T1040E, Version: 1.0, (0x85280010)

Core: e5500, Version: 2.0, (0x80241020)

Clock Configuration:

CPU0:1400 MHz, CPU1:1400 MHz, CPU2:1400 MHz, CPU3:1400 MHz,

CCB:600 MHz,

DDR:800 MHz (1600 MT/s data rate) (Asynchronous), IFC:150 MHz

FMAN1: 600 MHz

QMAN: 300 MHz

PME: 300 MHz

L1: D-cache 32 KiB enabled

I-cache 32 KiB enabled

Reset Configuration Word (RCW):

00000000: 0c18000e 0e000000 00000000 00000000

00000010: 66000002 80000002 ec027000 01000000

00000020: 00000000 00000000 00000000 00032810

00000030: 00000000 0342500f 00000000 00000000

Board: T1040RDB

Board rev: 0x01 CPLD ver: 0x06, vBank: 0

I2C: ready

SPI: ready

DRAM: Initializing....using SPD

Detected UDIMM 18KSF51272AZ-1G6K1

2 GiB left unmapped

DDR: 4 GiB (DDR3, 64-bit, CL=11, ECC on)

DDR Chip-Select Interleaving Mode: CS0+CS1

Flash: 256 MiB

L2: 256 KiB enabled

Corenet Platform Cache: 256 KiB enabled

Using SERDES1 Protocol: 102 (0x66)

NAND: 1024 MiB

MMC: FSL_SDHC: 0

PCIe1: Root Complex, no link, regs @ 0xfe240000

PCIe1: Bus 00 - 00

PCIe2: Root Complex, x1 gen1, regs @ 0xfe250000

02:00.0 - 8086:10d3 - Network controller

PCIe2: Bus 01 - 02

PCIe3: Root Complex, no link, regs @ 0xfe260000

PCIe3: Bus 03 - 03

PCIe4: Root Complex, no link, regs @ 0xfe270000

PCIe4: Bus 04 - 04

In: serial

Out: serial

Err: serial

Net: Initializing Fman

Fman1: Uploading microcode version 106.4.14

FSL_MDIO0:0 is connected to FM1@DTSEC1. Reconnecting to FM1@DTSEC2

FSL_MDIO0:0 is connected to FM1@DTSEC2. Reconnecting to FM1@DTSEC3

e1000: 68:05:ca:04:d5:6a

FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC4 [PRIME], FM1@DTSEC5, e1000#0

Warning: e1000#0 MAC addresses don't match:

Address in SROM is 68:05:ca:04:d5:6a

Address in environment is 00:04:9f:ef:00:00

Hit any key to stop autoboot: 0

The system auto boots and shows the following Linux login screen.

t1040rdb

root@t1040rdb:~#

Preparing board

QorIQ T1040 Reference Design Board User Guide, Rev. 0, 06/2015

Freescale Semiconductor, Inc.

Содержание QorIQ T1040





































































Результаты поиска

Содержание QorIQ T1040

Отзывы:

NXP Semiconductors QorIQ T1040, Руководство пользователя, Страница: 56 / 68

Результаты поиска

Содержание QorIQ T1040

Отзывы: