manualshive.com logo in svg

NXP Semiconductors QorIQ T1040, Руководство пользователя, Страница: 29 / 68

Поделиться
Скачать
NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 29

The enhanced SD host controller (eSDHC) provides an interface between the host system
and SD/MMC cards. Booting from the eSDHC interface is supported via the processor’s
on-chip ROM.

On the RDB, a single connector is used for both SD and MMC memory cards as shown
in the figure below.

T1040

SDHC_WP

SDHC_CD

SDHC_CLK

SDHC_CMD

SDHC_DAT[0:3]

Clamping

diodes

1V8

3V3

WP

CD

CLK

CMD

DAT[0:3]

SD Card

Figure 2-13. SDHC connection

2.13 USB interface

The T1040RDB board consists of two integrated USB 2.0 controllers that allow direct
connection to the USB ports with appropriate protection circuitry and power supplies.
The USB features are as follows:

• High-speed (480 Mbit/s), full-speed (12 Mbit/s), and low-speed (1.5 Mbit/s)

operation

• Host mode
• Dual stacked Type A connection

The USB ports are connected to a standard Type A connector (USB1 and USB2) for
compatibility with most USB peripherals.

Power for the ports is provided by a MIC2506YM switch, which supplies 5 V at up to 1
A per port. The power-enable and power-fault-detect pins are connected directly to the
T1040 for individual port management.

The figure below shows the USB connectivity on the T1040RDB board.

Chapter 2 Architecture

QorIQ T1040 Reference Design Board User Guide, Rev. 0, 06/2015

Freescale Semiconductor, Inc.

29

Содержание QorIQ T1040





































































Отзывы:

Нет отзывов