manualshive.com logo in svg

NXP Semiconductors QorIQ T1040, Руководство пользователя, Страница: 34 / 68

Поделиться
Скачать
NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 34

The table below displays the connections made from the T1040RDB COP Connector.

Table 2-6. JTAG header definition

Pin#

Signal name

Connection

1

TDO

Connected directly between the processor and JTAG/COP connector.

2

NC

Not connected

3

TDI

Connected directly between the processor and JTAG/COP connector

4

TSRT

Routed to the RESET PLD. TRST to the processor is generated from the PLD.

5

NC

Not connected

6

VDD_SENSE

Pulled to 3.3V via a 10 Ohm resistor

7

TCK

Connected directly between the processor and JTAG/COP connector.

8

CKSTP_IN

Connected directly between the processor and JTAG/COP connector.

9

TMS

Connected directly between the processor and JTAG/COP connector.

10

NC

Not connected

11

SRESET

Routed to the RESET PLD. SRESET to the processor is generated from the PLD.

12

GND

Connected to ground

13

HRESET

Routed to the RESET PLD. SRESET to the processor is generated from the PLD.

14

KEY

Not connected

15

CSKTP_OUT

Connected directly between the processor and JTAG/COP connector

16

GND

Connected to ground

2.17 Connectors, headers, jumper, push buttons and LED

This section explains:

• Connectors
• Headers
• Jumper
• Push buttons
• LEDs

The figure below shows the diagram of T1040RDB platform.

Connectors, headers, jumper, push buttons and LED

QorIQ T1040 Reference Design Board User Guide, Rev. 0, 06/2015

34

Freescale Semiconductor, Inc.

Содержание QorIQ T1040





































































Отзывы:

Нет отзывов