manualshive.com logo in svg

NXP Semiconductors MAC57D5 Series, Руководство пользователя, Страница: 7 / 30

Поделиться
Скачать
NXP Semiconductors MAC57D5 Series Скачать руководство пользователя страница 7

When power is applied to the EVB, five green LED’s adjacent to the voltage regulators show the presence of the supply
voltages as follows:

Table 4. Power status LEDs

BOARD

REFERENCE

DESCRIPTION

MAC57D5MB

DS2

Indicates that the 12 V is connected to the EVB correctly.

DS4

Indicates that the 5 V switching regulator is enabled and
working correctly.

DS3

Indicates that the 3.3 V switching regulator is enabled and
working correctly.

DS5

Indicates that the 1.25 V switching regulator is enabled and
working correctly.

DS1

Indicates that the TFT Display – switching regulator is
enabled and working correctly.

MAC57D5-208DC
MAC57D5-506DC

DS1

Indicates that the 1.8 V switching regulator is enabled and
working correctly.

DS2

Indicates that the 0.9 V switching regulator is enabled and
working correctly.

If no LED’s are illuminated when power is applied to the EVB and the regulators are correctly enabled using the appropriate
jumpers, it is possible that either power switch SW1 is in the “OFF” position or some jumper is missed, please refer to 

MCU

power supply jumpers

.

6 MCU power supply jumpers

Table 5. MCU power supply jumpers

BOARD

REFERENCE

POSITION

PCB

LEGEND

DESCRIPTION

MAC57D5-208DC

J2

1-2 (Default)

5.0 V switching regulator output is routed to
VDDEH_ADC_MCU and VDDA_MCU (MCU)

2-3

3.3 V switching regulator output is routed to
VDDEH_ADC_MCU and VDDA_MCU (MCU)

REMOVED

VDDEH_ADC_MCU and VDDA_MCU are not
powered (disabled).

J1

1-2 (Default)

5.0 V switching regulator output is routed to
VDDM_SMD_MCU (MCU)

2-3

3.3 V switching regulator output is routed to
VDDM_SMD_MCU (MCU)

REMOVED

VDDM_SMD_MCU is not powered (disabled).

MAC57D5-516DC

J21

1-2 (Default)

3.3 V switching regulator output is routed to
VDDE_A_MCU (MCU)

REMOVED

VDDE_A_MCU is not powered (disabled).

J22

1-2 (Default)

3.3 V switching regulator output is routed to
VDDE_B_MCU (MCU)

Table continues on the next page...

MCU power supply jumpers

MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016

Freescale Semiconductor, Inc.

7

Содержание MAC57D5 Series































Отзывы:

Нет отзывов