manualshive.com logo in svg

NXP Semiconductors MAC57D5 Series, Руководство пользователя, Страница: 28 / 30

Поделиться
Скачать
NXP Semiconductors MAC57D5 Series Скачать руководство пользователя страница 28

NOTE

Caution - Before fitting or removing a daughter card, ensure the EVB is not powered.

Figure 13. MCU Daughtercard connectors

NOTE

• Caution - Gently place the daughtercard on the EVB connectors ensuring the

correct orientation as per the picture. The connectors are polarized so the
daughtercard will only fit in one orientation (with the jumpers at the bottom of the
daughtercard). Once the inter board connectors have been located correctly, firmly
push down all four corners of the daughter card simultaneously in order to ensure
the connectors are mated.

• In order to prevent damage to the daughtercard connectors, it is important to

remove the daughtercard correctly. Carefully lift either the top or bottom edge of
the daughtercard and it should the easily lift off as shown in next the picture.

• Do NOT attempt to lift the left or right edge of the daughtercard as this will result

in connector damage

Jumper Default Configuration

MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016

28

Freescale Semiconductor, Inc.

Содержание MAC57D5 Series































Отзывы:

Нет отзывов