manualshive.com logo in svg

NXP Semiconductors MAC57D5 Series, Руководство пользователя, Страница: 6 / 30

Поделиться
Скачать
NXP Semiconductors MAC57D5 Series Скачать руководство пользователя страница 6

5.3 Power jumpers of Regulators

All of the voltage regulators (switching and linear) are powered from the main 12 V supply line by a jumper with the
exception of the 3.3 V and 1.8 V linear regulator which has a two way jumper to allow selection of the input voltage. The
table below details the jumper configurations for the linear 1.25 V regulator source voltage. By default, the regulator is
powered from a 12 V supply line.

Table 3. Regulators power jumpers

BOARD

REFERENCE

POSITION

PCB

LEGEND

DESCRIPTION

MAC57D5MB

J32

1-2 (Default)

-

PMIC - switching regulators [5 V, 3.3 V and
1.25 V] are powered from VBAT [12 V].

REMOVED

-

PMIC - switching regulators [5 V, 3.3 V and
1.25 V] are not powered.

J35

1-2 (Default)

-

5.0 V switching regulator output is enabled

2-3

-

5.0 V switching regulator output is disabled

REMOVED

-

5.0 V switching regulator output is disabled

J36

1-2 (Default)

-

3.3 V switching regulator output is enabled

2-3

-

3.3 V switching regulator output is disabled

REMOVED

-

3.3 V switching regulator output is disabled

J37

1-2 (Default)

-

1.25 V switching regulator output is manually
enabled

2-3

-

1.25 V switching regulator output is disabled

REMOVED

-

1.25 V switching regulator output is controlled
by the MCU

J30

1-2 (Default)

-

5.0 V switching regulator output is routed to
all peripherals on the EVB.

REMOVED

-

5.0 V switching regulator output is
disconnected from all peripherals on the
EVB. (Disabled)

J26

1-2 (Default)

-

3.3 V switching regulator output is routed to
all peripherals on the EVB.

REMOVED

-

3.3 V switching regulator output is
disconnected from all peripherals on the
EVB. (Disabled)

J33

1-2 (Default)

-

1.25 V switching regulator output is routed to
all peripherals on the EVB.

REMOVED

-

1.25 V switching regulator output is
disconnected from all peripherals on the
EVB. (Disabled)

5.4 Power status LED’s and Fuse

Initial configuration

MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016

6

Freescale Semiconductor, Inc.

Содержание MAC57D5 Series































Отзывы:

Нет отзывов