Nussbaum TOP LIFT TSK 12000 DJ Скачать руководство пользователя | Manualshive

Страница: 26 / 56

background image

Operating Manual and Inspection Book

TOP LIFT TSK 12000 DJ

- 26 -

4. Installation

The installation of the Lift is performed by manufacturer trained technicians or by the
manufacturer’s distribution partner. The Lift owner may use their trained mechanics
to install the Lift. The installation must be performed according to the following regu-
lations:
•

Use architectural plans, if available, to determine Lift location.

•

Lift is intended for indoor installation only. Installation in an outdoor application is
prohibited and will void the warranties of the product.

•

Always consult a qualified person regarding local regulations for seismic require-
ments. The owner has to consult a qualified person to address any local or state
requirements (per the ALCTV standard: “a qualified person should be consulted
to address any seismic loads and other local or state requirements”)

•

Do not install Lift in hazardous locations, pit or depression areas, or washing stalls.

•

Concrete must have compression strength (see chapter 8).

•

Mount on a foundation deeper than the local external frost line.

•

Be sure to read the ANSI/ALI ALIS prior to installation.

•

The installer has to return the instructional materials furnished with the lift back to
the owner

«
...
24
25
26
27
28
...
»

Содержание TOP LIFT TSK 12000 DJ

























































Отзывы:

Нет отзывов

Похожие инструкции для TOP LIFT TSK 12000 DJ

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Markoprint iJET

Бренд: Weber Страницы: 127

Blue Thunder Series

Бренд: Miller Страницы: 36

Бренд: WALTCO Страницы: 39

Бренд: Gage Страницы: 36

Бренд: AXEM Technology Страницы: 31

Бренд: Feig Electronic Страницы: 35

Taurus **5 Basic S Series

Бренд: EWM Страницы: 41

DE-3000+ Series

Бренд: Altronic Страницы: 77

Бренд: Poweramp Страницы: 40

IDEALARK RSR 375-I

Бренд: Lincoln Electric Страницы: 28

Бренд: Lincoln Electric Страницы: 35

Бренд: Madas Страницы: 40

Бренд: Bishamon Страницы: 7

Бренд: morse Страницы: 6

Бренд: Draper Страницы: 28

Бренд: Eastwood Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды