Nussbaum POWER LIFT HF 7000 Скачать руководство пользователя

Страница: 7 / 76

OPI-POWER LIFT HF 7000-8000-V1.0-EN

• After each set down of the vehicle, check the lift-

ing arm positions below the fixture points again

and adjust as required.

• When disassembling heavy, consider any possible

centre of mass shifts. The vehicle is to be appro-

priately secured using suitable materials (e.g. ten

sioning belts, beams, etc.) against falling.

• After design and maintenance on load bearing

parts the lift must be inspected by a technical ex

pert.

•

Vehicles may only be attached at fixture points

approved by the vehicle manufacturer.

• The entire lifting and lowering process is to be

continuously observed.

• Initial access to the lift is only permitted after the

main switch has been turned off and secured,

and the operating lever is additionally secured

against unauthorised use.

Save these instructions!

1.6 Safety devices

Nussbaum has designed several saftety features

into each Lift to ensure safe and efficient opera

tions under a variety of conditions. Warranties will

be voided and dangerous working conditions exist

if any of the listed devices are altered or disabled.

•

Over-pressure valve

Hydraulic system fuse against over-pressure.

•

Check valve

Secure the vehicle against unauthorised lower-

ing.

•

Main switch with curtain lock device

Fuse to prevent unauthorised use.

•

Command / downstream system with latch

Secure against unauthorised lowering of the lift.

•

Deadman controls

Lift movement stops when the operating lever is

released.

•

Lifting arm block

Secures the lifting arm against horizontal move-

ment in a lifted condition.

Содержание POWER LIFT HF 7000













































































Результаты поиска

Содержание POWER LIFT HF 7000

Отзывы:

Похожие инструкции для POWER LIFT HF 7000

Бренды по названию

Популярные бренды

Nussbaum POWER LIFT HF 7000, Руководство по эксплуатации и книга учета инспекций

Результаты поиска

Содержание POWER LIFT HF 7000

Отзывы:

Похожие инструкции для POWER LIFT HF 7000

Бренды по названию

Популярные бренды