310HD IP Phone
Administrator's Manual
84
Document #: 299-13801
Parameter
Description
"Portugal"
"USA"
voip/regional_settings/u
se_acl_conf_configurati
on
Enables the user defined CPT. When this parameter is enabled, the
selected_country
parameter
is not relevant and the below Call Progress
Tones values can be determined by the user.
0 = Disable
1 = Enable
Call Progress Tones (CPT)
Note:
Up to 10 CPT’s can be configured (voip/regional_settings/call_progress_tones/0…9).
voip/regional_settings/c
all_progress_tones/0/ton
e_enabled
Enables the specific CPT.
0 = Disable
1 = Enable
voip/regional_settings/c
all_progress_tones/0/ton
e_name
Defines the name of the CPT.
voip/regional_settings/c
all_progress_tones/0/ton
e_cadence_type
Defines the cadence type of the tone.
0 = Continuous signal
1 = Cadence signal
2 = Burst signal
voip/regional_settings/c
all_progress_tones/0/fre
quency_a
Defines the low frequency (in Hz) of the tone.
The valid value range is 300 to 1980 Hz, in steps of 1 Hz. Unused frequencies
must be set to zero.
voip/regional_settings/c
all_progress_tones/0/fre
quency_b
Defines the high frequency (in Hz) of the tone.
The valid value range is 300 to 1980 Hz, in steps of 1 Hz. Unused frequencies
must be set to zero.
voip/regional_settings/c
all_progress_tones/0/fre
quency_a_level
Output level of the low frequency tone (in -dBm) in Call Progress generation.
The valid value range is from -62 dBm to 0 dBm (where -63 dBm is mute).
voip/regional_settings/c
all_progress_tones/0/fre
quency_b_level
Output level of the low frequency tone (in -dBm) in Call Progress generation.
The valid value range is from -62 dBm to 0 dBm (where -63 dBm is mute).
voip/regional_settings/c
all_progress_tones/0/ton
e_on_0
tone_on_0 to tone_on_3.
If the signal is Cadence or Burst, then this value represents the on duration. In
the case of a Continuous tone, this value represents the minimum detection
time. The units are in 10 msec.
voip/regional_settings/c
all_progress_tones/0/ton
e_off_0
tone_off_0 to tone_on_3.
If the signal is Cadence, then this value represents the off duration. The units
are in 10 msec. If it is not used, then set it to zero. If the signal is Burst, only
tone_off 0 is relevant. It represents the off time that is required from the end of
the signal to the detection time.
Содержание 310HD series
