NuAire LabGard ES NU-543-300S Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 72

background image

OM0239

Page 61 of 72

April 2021

9.0

Remote Contacts

The NU-543S has several contact closures for remote sensing of various functions.

9.1 Fan Relay

The fan relay contacts are normally open and closed contact closure outputs that are activated whenever the blower key is
pressed and the blower key LED indicator is on or blinking. Contact ratings are 250 VAC maximum at 2 Amps.

9.2 Alarm Relay

The alarm relay contacts are normally open and closed contact closure outputs which are activated whenever an airflow
alarm condition occurs. Contact ratings are 250 VAC maximum at 2 Amps.

9.3 15VDC Output

The 15VDC (100mA) output is active when power is applied to the

FlowGard™

control board.

«
...
59
60
61
62
63
...
»

Содержание LabGard ES NU-543-300S









































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard ES NU-543-300S

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: ParaBody Страницы: 4

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 7

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 24

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Bacharach Страницы: 2

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: iHealth Страницы: 8

Бренд: LA Audio Страницы: 9

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды