NuAire LabGard ES NU-543-300S Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 72

background image

OM0239

Page 43 of 72

April 2021

7.5.3

Setpoint Parameters

Setpoint parameters establish both the nominal airflow velocity, as well as the alarm limit velocities. Typically
theses are default values factory set for the required airflow range as tested and listed by 3

rd

party agencies.

However, they may be altered in special cases for modified non-listed special cabinets.  In addition to setpoints,
filter life parameters are established using motor rpm.  To determine filter life, the starting motor rpm is entered
after the first airflow calibration is performed with clean filters.  The maximum rpm is a known fixed value based
on the DC ECM motor used.  The difference between the maximum and current rpm determines the filter life
percentage.  The filter life percentage starts at 100% and as the current rpm increases due to filter loading, the
filter life decreases.

Inflow Velocity

Default values

Low Limit .46fpm

Setpoint .53fpm

High Limit .61fpm

Filter Life

Filter Life Calibration

Maximum rpm

–

initial rpm = Total available rpm

Total available rpm

–

latest rpm = Filter rpm available

Filter rpm available ÷total available rpm = (Filter rpm used -1) x 100=HEPA filter life

Setpoints

Inflow
Filter Life
DnFlow Set Pt .30

Inflow Velocity (fpm)

Low Limit:                       .46
Setpoint:                                       .53
High Limit:                                    .61

Filter Life

Initial rpm:                                   1000
Latest rpm:                      1100
Maximum rpm:             1375

«
...
41
42
43
44
45
...
»

Содержание LabGard ES NU-543-300S









































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard ES NU-543-300S

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Makita Страницы: 84

Бренд: NEILPRYDE Страницы: 53

Бренд: 3Disc Страницы: 12

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: Dana Design Страницы: 20

Бренд: Echo Страницы: 6

Pro Attachment Series

Бренд: Echo Страницы: 28

Бренд: Echo Страницы: 2

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Gearmore Страницы: 47

Бренд: Xtool Страницы: 51

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: R&S Страницы: 371

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды