NuAire LabGard ES NU-543-300S Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 72

background image

OM0239

Page 54 of 72

April 2021

7.10 Main Control Board Description and Replacement

To access the main control board for fuse or board replacement, remove screws at each upper side of the control center
and allow the control center to rotate down, resting on the safety straps. Now the main control board is exposed for
service.

7.10.1 Main Control Board Replacement

The main control board consists of one Printed Circuit Board (PCB) assembly.
The PCB contains the power supply, configuration switch, sensor inputs/outputs and control inputs/outputs
components and display.

7.10.2 Main Control Board Fuse Replacement

Disconnect electrical power from cabinet before fuse replacement.

All AC circuits are fuse protected and when replacement is necessary, USE ONLY FUSES OF SAME TYPE AND RATING
FOR PROTECTION AGAINST RISK OF FIRE.

DESCRIPTION:

BLOWER FUSE

OUTLET FUSE

ACCESSORY

OUTPUT FUSE

LIGHT FUSE

FUSE TYPE:

TIME-LAG

TIME-LAG

TIME-LAG

TIME-LAG

FUSE SIZE:

1/4 X 1-1/4 INCH

5 X 20MM

5 X 20MM

5 X 20MM

NU-543-300S

6.25 AMPS

3 AMPS (2)

2 AMPS

1 AMP (2)

NU-543-400S

8 AMPS

3 AMPS (2)

2 AMPS

1 AMP (2)

NU-543-500S

10 AMPS

3 AMPS (2)

2 AMPS

1 AMP (2)

NU-543-600S

10 AMPS

3 AMPS (2)

2 AMPS

1 AMP (2)

7.10.3 Main Control Board Replacement

Note: All setup and calibration data will be lost, the memory reinitialized to the default values and all control

functions reset to an initial cabinet power condition.

If possible, before the main control board replacement, it would be preferred to know the operational

parameters of the cabinet, (i.e. blower speed/PWM signal DC voltage setpoints if modified and airflow data

from previous certification).

Disconnect electrical power from the cabinet before attempting any
maintenance action.

The main control board is fastened to the control center with (6) 6-32 studs/nuts. All electrical connections are
made with removable terminals and/or Faston connectors except for the motor/blower connector which uses a
screw terminal. Remove all electrical connections and fasteners and then remove the main control board from the
control center.

Install new main control board by reattaching all electrical connections and fasteners. Once installed, rotate
control center to normal position and fasten in place.

Reconnect power to cabinet.

CAUTION

!

CAUTION

!

«
...
52
53
54
55
56
...
»

Содержание LabGard ES NU-543-300S









































































Отзывы:

Нет отзывов

Похожие инструкции для LabGard ES NU-543-300S

Бренд: Taber Страницы: 27

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: Raytech Страницы: 21

Бренд: Teac Страницы: 2

Бренд: laerdal Страницы: 2

Бренд: Baileigh Industrial Страницы: 40

Бренд: Kawai Страницы: 10

Бренд: Danelec Страницы: 67

Бренд: XM Fitness Страницы: 10

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FASTERHOLT Страницы: 96

SC 2 Deluxe EasyFix

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 16

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренд: laerdal Страницы: 104

Бренд: laerdal Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды