Nortrac NorTrac 70XTC Скачать руководство пользователя

Страница: 44 / 112

Operation Description

Figure 2-41 Power Output Device Operation

1. High Gear 2.

Neutral gear

3. Low Gear

2.16.8 Power Take Off (PTO) Shaft Use

To connect and disconnect power to the power take off (PTO) shaft the double-acting clutch, the PTO gear shift

handle, and the PTO disconnect control handle are used. When the clutch pedal is pushed down part way it

disconnects the engine clutch, and when it is pushed down all the way down it disconnects the PTO clutch.

When the PTO gear shift handle is pushed forwards, it will be in high gear. When the PTO handle is pulled

backwards, it will be in low gear. Use the following method:



Remove the rear hitch (only when using the 3-point configuration) and the protective cover on the power take

off (PTO) shaft and connect the farm implement drive to the PTO shaft on the tractor.



Depress the clutch pedal to the floor to disconnect the PTO clutch and put the PTO gear shift handle in the

required position (high or low).



Depress the clutch pedal to the floor again and turn the PTO disconnect control handle to the

―connected‖ position.



Release the clutch pedal slowly. First operate with the throttle at low speed to check whether the PTO is

working properly, and then start working.



When repeated work in the same place within a short time frame is required, step on the clutch pedal gently to

disconnect the main clutch. This cuts off the power to the tractor transmission, and the tractor stays in one place

while the farm implement behind it can still work normally.



To disconnect the PTO depress the clutch pedal to the floor and turn the PTO disconnect control handle to

the ―disconnected‖ position. The PTO gear shift handle does not need to be moved. The PTO shaft will

stop turning.



After disconnecting the farm implement from

the PTO shaft, reinstall the protective cover

over the PTO shaft. Replace the rear hitch if it

had been removed.

WARNING

Do not attach or detach anything from the PTO shaft while it is turning. Attempting to do so

can cause damage to the equipment and serious injury.

Содержание NorTrac 70XTC

















































































































Результаты поиска

Содержание NorTrac 70XTC

Отзывы:

Похожие инструкции для NorTrac 70XTC

Бренды по названию

Популярные бренды

Nortrac NorTrac 70XTC, Руководство пользователя

Результаты поиска

Содержание NorTrac 70XTC

Отзывы:

Похожие инструкции для NorTrac 70XTC

Бренды по названию

Популярные бренды