background image

Regulatory Information

•  Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.

•  Changes or modifications not expressly approved by the manufacturer could void the user’s authority to 

operate the equipment.

•  Les changements ou modifications non approuvés expressément par la partie responsable de la 

conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.

•  This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference and (2) this device must 
accept any interference received, including interference that may cause undesired operation.

•  Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts 

de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire 
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le 
brouillage est susceptible d’en compromettre le fonctionnement.

Regulatory Information 

NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION:

 

THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS

 

PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE 

www.dtsc.ca.gov/hazardouswaste/perchlorate

KEEP AWAY FROM SMALL CHILDREN. IF BATTERY IS SWALLOWED, PROMPTLY SEE A DOCTOR. 

DO NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL OF USED BATTERIES MUST BE MADE IN

 

ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.

   WARNING   

This operator system is equipped with an unattended 
operation feature. This door could move unexpectedly. NO 
ONE SHOULD CROSS THE PATH OF A MOVING DOOR!

   WARNING   

This system can be installed on sectional type (roll up) doors only 
per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!

   WARNING   

The Remote Command Transceiver must be mounted in the 
garage, in sight of the garage door, where the visual and 
audible movement warning indicators can be clearly seen 
and heard.

   WARNING   

Do not install the Remote Command Transceiver on garage 
door operators manufactured prior to 1993 (models without 
an operational safety beam entrapment detection system).

Содержание ADT Pulse GD00Z-8-ADT

















Отзывы: