Nordyne M4RC-072D-35C Скачать руководство пользователя страница 6

Страница: 6 / 48

COMBUSTION AIR & VENTING REQUIREMENTS

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for

each appliance connected to the venting system

being placed into operation could result in carbon

monoxide poisoning or death.
The following steps shall be followed with each

individual appliance connected to the venting

system being placed in operation, while all other

appliances connected to the venting system are

not in operation:

1. Seal any unused openings in the venting system.
2. Inspect the venting system for proper size and

horizontal pitch, as required in the

National Fuel

Gas Code, ANSI Z223.1/NFPA 54 or the CSA
B149.1, Natural Gas and Propane Installation
Codes

and these instructions. Determine that

there is no blockage or restriction, leakage,

corrosion and other deficiencies which could

cause an unsafe condition.

3. As far as practical, close all building doors and

windows and all doors between the space in

which the appliance(s) connected to the venting

system are located and other spaces of the

building.

4. Close fireplace dampers.
5. Turn on clothes dryers and any appliance not

connected to the venting system. Turn on

any exhaust fans, such as range hoods and

bathroom exhausts, so they are operating at

maximum speed. Do not operate a summer

exhaust fan.

6. Follow the lighting instructions. Place the

appliance being inspected into operation.

Adjust the thermostat so appliance is operating

continuously.

7. Test for spillage from draft hood equipped

appliances at the draft hood relief opening after

5 minutes of main burner operation. Use the

flame of a match or candle.

8. If improper venting is observed during any of

the above tests, the venting system must be

corrected in accordance with the

National Fuel

Gas Code, ANSI Z223.1/NFPA 54 and/or CSA
B149.1, Natural Gas and Propane Installation
Codes.

9. After it has been determined that each appliance

connected to the venting system properly vents

when tested as outlined above, return doors,

windows, exhaust fans, fireplace dampers and

any other gas-fired burning appliance to their

previous conditions of use.

WARNING:

RISQUE D’EMPOISONNEMENT AU

MONOXYDE DE CARBONED

Le non-respect des consignes suivantes portant

sur chacun des appareils raccordés au système

d’évacuation mis en service pourrait entraîner

l’empoisennement au monoxyde de carbone ou

la mort. Les consignes suivantes doivent être

observées pour chaque appareil raccordé au système

d’évacuation mis en service si les autres appareils

raccordés au système ne sont pas en service:
1. Sceller toute ouverture non utilisée de la systéme

d’évacuation;

2. S’assurer que la systéme d’évacuation présente des

dimensions et une pente horizontale conformes à la

norme ANSI Z223.1/NFPA 54, intitulée National Fuel

Gas Code ou aux codes d’installation CSA-B149.1,

ainsi qu’aux présentes instructions. S’assurer que la

systéme d’évacuation n’est pas bloquée, restreinte,

corrodée, qu’elle ne fuit pas et qu’elle ne présente

aucun autre défaut potentiellement dangereux;

3. Dans la mesure du possible, fermer toutes les portes

et fenêtres du bâtiment, et toutes les portes entre la

pièce où se trouve l’appareil raccordé à la systéme

d’évacuation et les autres pièces du bâtiment.

4. Fermer les registres des foyers;
5. Mettre en service les sécheuses et tout autre appareil

qui n’est pas raccordé à la systéme d’évacuation.

Faire fonctionner à régime maximal tout ventilateur

d’évacuation, tel que les hottes de cuisinière et les

ventilateurs de salles de bains. Ne pas mettre en

service les ventilateurs d’été.

6. Respecter les instructions d’allumage. Mettre en

service l’appareil à l’essai. Régler le thermostat

de manière à ce que l’appareil fonctionne sans

interruption;

7. Vérifier s’il y a débordement à l’orifice d’évacuation

du coupe tirage des appareils dotés d’un coupe

tirage 5 minutes après l’allumage du brûleur

principal. Utiliser la flamme d’une allumette ou

d’une chandelle.

8. Si l’on constate, au cours de l’un des essais qui

précèdent, que l’évacuation est déficiente, corriger

le système d’évacuation conformément à la norm

ANSI Z223.1/NFPA 54, National Fuel Gas Code, et

(ou) aux codes d’installation CSA B149.1.

9. Après avoir déterminé que tous les appareils

raccordés à la systéme d’évacuation évacuent

correctement tel que prescrit ci-dessus, rouvrir les

portes et les fenêtres et remettre les ventilateurs

d’évacuation, les registres de foyers et tout

autre appareil fonctionnant au gaz à leur état de

fonctionnement initial.

AVERTISSEMENT

Содержание M4RC-072D-35C

















































Результаты поиска

Содержание M4RC-072D-35C

Отзывы:

Похожие инструкции для M4RC-072D-35C

Бренды по названию

Популярные бренды

Nordyne M4RC-072D-35C, Руководство по установке

Результаты поиска

Содержание M4RC-072D-35C

Отзывы:

Похожие инструкции для M4RC-072D-35C

Бренды по названию

Популярные бренды