Nordson Versa-Spray II Скачать руководство пользователя страница 13

Страница: 13 / 64

Installation

3-1

Part 107016-02

2016 Nordson Corporation

Section 3

Installation

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

Gun Mounting

1. See Figure 3-1. Install the mounting bar clamp (1) on a 25.4-mm (1-in.)

diameter bar (2). Tighten handle B.

2. Loosen the set screws (5) in the gun mount (4) and insert the end of the

mounting bar (3) in the mount. Tighten the set screws securely.

3. Use knob A to adjust the angle of the spray gun. Use handle B to

position the clamp (1) vertically or horizontally. Use handle C to adjust

the angle and length of the mounting bar.

1400410B

Figure 3-1

Gun Mounting—Shur-Lok Gun Mount

1. Mounting bar clamp
2. 25.4-mm (1-in.) bar
3. Mounting bar

4. Shur-Lok gun mount
5. Set screws

6. Hose bracket
7. Hose adapter

Note:

Refer to

Gun Mounting Bar

in the

Options

section for ordering information about the mounting bar (3).

Содержание Versa-Spray II

































































Результаты поиска

Содержание Versa-Spray II

Отзывы:

Похожие инструкции для Versa-Spray II

Бренды по названию

Популярные бренды

Nordson Versa-Spray II, Руководство пользователя по изделию

Результаты поиска

Содержание Versa-Spray II

Отзывы:

Похожие инструкции для Versa-Spray II

Бренды по названию

Популярные бренды