background image

 

PAGE 10 OF 13 

 

ISSUE 1 

 

02 2006

 

 
 
 

DRIVE SHAFT:- ________________________________________________________________  

To avoid internal damage (especially due to torque overload), the output drive shaft has been designed to 
shear first.  This saves major internal damage and allows easy shaft removal. 

 

 

Figure 8 

 

 

To replace drive shaft: 

 

Support tool securely in a horizontal position, before commencing this operation 
 
1. 

Using a suitable punch, remove spring pin (A). 

 

2. 

Remove remainder of drive shaft (B). 

 

 
Again securely support the tool in a horizontal position. 
 
3. 

Taking new drive shaft (B) (#77112.2) insert splined end into the reaction foot (C) insuring correct 
engagement of spline and that the drive shaft is pressed fully home. 

 

4. 

To secure drive shaft insert new pin (A) (#26287) with suitable punch. 

 
 

CLEANING:- __________________________________________________________________  

Keep the tool in a clean condition to aid safety.  Do not use abrasives or solvent based cleaners. 
 

TIP:  Holding the tool vertically with the reaction foot downward, lightly tap the complete tool on the 
 

bench, until the remainder of the broken shaft drops out. 

Содержание PNEUTORQUE PTME-72-1000
















Отзывы: