background image

 

PAGE 5 OF 13 

 

ISSUE 1 

 

02 2006

 

 
 

 

SETTING CLOCKWISE/COUNTER-CLOCKWISE OPERATION_________________________  

 
 

 

Clockwise

 

(Arrow towards drive square) 

Figure 2a 

 
 
 

 
 
 

 
 

Counter-clockwise 

(Arrow away from drive square) 

Figure 2b 

 
 
 
 
 

TIP:  To help set the clockwise / counter-clockwise operation run the tool in 

neutral

 position before 

re-engaging. 

 
 
 
 

Neutral position 

Figure 2c 

 
 
 
 

 
 

WARNING: 

FAILURE TO FULLY ENGAGE THE CLOCKWISE/COUNTER- 
CLOCKWISE OPERATION SELECTOR WILL RESULT IN DAMAGE TO 
THIS PART OF THE GEARBOX. 

 
 

SETTING TORQUE FOR BOLT TIGHTENING _______________________________________  

The tools use the air pressure set on an external pressure regulator unit to determine the stall torque.  
Pneutorques® are supplied with an Air Pressure Graph which relates torque output to air pressure.  Set 
the torque output as follows:- 

1.  Ensure the Clockwise/Counter-clockwise Selector (if fitted) is correctly set. 

2.  Establish the air pressure required using the Air Pressure Graph. 

3.  With the tool running, adjust the pressure regulator until the correct figure is shown on the gauge. 

IMPORTANT: 

THE WRENCH MUST BE FREE RUNNING WHILE ADJUSTING THE AIR PRESSURE 
TO GIVE THE CORRECT SETTING. 

IMPORTANT: 

ENSURE THE LUBRO CONTROL UNIT IS SUPPLYING APPROXIMATELY SIX 
DROPS OF OIL PER MINUTE WHILE THE TOOL IS FREE RUNNING. 

 

Содержание PNEUTORQUE PTME-72-1000
















Отзывы: