Nolan N70-2 GT, Инструкции по безопасности и эксплуатации

Страница: 20 / 136

20
N70-2 GT
- Scratched PINLOCK
®
visors and inner visors may cause reduced visibility and
must therefore be replaced.
- Regularly check the correct stretch of the PINLOCK ® inner visor to prevent it from
moving and scratching both surfaces.
- If the helmet visor fogs up and/or condensation forms between the visors, check
that the PINLOCK ® inner visor is both correctly assembled and stretched.
- An excessive and early stretch of the PINLOCK
®
inner visor may result in exces-
sive adherence against the visor surface and/or permanent deformations with
subsequent inability to correctly perform any following adjustments.
- Intense sweating/breathing, the use under particular weather conditions (low tem-
peratures, high humidity, sudden changes in temperature or heavy rain) or intense
and prolonged use may affect the performance of the PINLOCK ® inner visor and
cause fogging or formation of condensation. In such cases, to restore the sys-
tem ef fi ciency after using the helmet, remove the PINLOCK
®
inner visor from the
helmet visor and let it dry with dry and warm air. The same procedure must be
applied to the helmet, in order to dry out humidity in case it has formed up as a
consequence of the conditions described above.
3 DISASSEMBLING THE PINLOCK
®
INNER VISOR
3.1 Remove the visor equipped with the PINLOCK
®
inner visor (see instructions
above).
3.2 Widen the visor and release the PINLOCK
®
inner visor from the pins (Fig.13).
3.3 Release the visor.
4 MAINTENANCE AND CLEANING OF THE PINLOCK
®
INNER VISOR
4.1 Remove the PINLOCK
®
inner visor from the visor. Using a damp and soft cloth,
gently clean it with neutral liquid soap. Remove the soap under running water.
4.2 Dry the visor with dry and warm air without wiping it.
4.3 To keep the features of the visor in good conditions over time, let the helmet dry
in a ventilated and dry place with the visor open after use. Keep it away from heat
sources and store it in a place away from direct light.
4.4 Do not use solvents or chemical products.
VISION PROTECTION SYSTEM (VPS)
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN™ (*) polycar-
bonate moulded sunscreen with scratch-resistant/fog-resistant treatment. It is very
simple and practical to use: just lower it to activate it or lift it to remove it from the fi eld
of vision. It is useful in all sorts of situations, both on long journeys out of town and
shorter town trips.
Moreover, the innovative fastening system allows you to assemble and disassemble
the sunscreen without the need of any tools for ordinary maintenance and cleaning
operations.
1 VPS OPERATION
The VPS mechanism allows to activate the sunscreen by simply lowering it until it par-
tially covers the visor fi eld of vision. In this way, the desired light transmittance reduc-
tion is achieved.
(*) LEXAN is a trademark of SABIC.
2.2 Insert the external part “B” of the visor air intake in the hole provided in the visor
and engage from inside the air diffuser “A” by applying pressure to the two side
centring and hooking pins (Fig.10).
2.3 Fix the visor onto the helmet (see instructions above).
WARNING
- Ensure that the side inserts have been correctly assembled. Open and close the
visor ensuring that the side inserts remain in their positions. If necessary, repeat
the above-mentioned operations.
- Ensure that the air intake is securely fastened to the visor by opening and closing
the outer fl ap. If necessary, repeat the above-mentioned operations.
- Do not use the helmet without having assembled the side inserts and air intake of
the visor correctly.
- In case of malfunctioning or damages, please contact an authorised Nolangroup
dealer.
(Available as standard or accessory/spare part)
1 ASSEMBLING THE PINLOCK
®
INNER VISOR
1.1 Disassemble the visor (see instructions above).
1.2 Make sure that the inner surface of the visor is clean and ensure that the pin ad-
justment external levers are turned inwards (Fig.11).
1.3 Place the PINLOCK
®
inner visor on the visor.
The silicone-sealed pro fi le of the PINLOCK ® inner visor must be in contact with
the inner surface of the visor.
1.4 Insert one side of the PINLOCK
®
inner visor into one of the visor pins and hold it in
position (Fig.12).
1.5 Widen the visor and fi t the second side of the PINLOCK
®
inner visor to the other
pin (Fig.13).
1.6 Release the visor.
1.7 Remove the protective fi lm from the PINLOCK ® inner visor and check that the
entire silicone-sealed pro fi le of the inner visor adheres to the visor.
1.8 Fix the visor onto the helmet (see instructions above).
2 CHECKING AND ADJUSTING THE PINLOCK
®
INNER VISOR STRETCH
Check for the correct assembly of the PINLOCK
®
inner visor by opening and closing the
visor and ensuring that they do not move with respect to each other.
Should the PINLOCK ® inner visor not be tightly fi xed to the visor, simultaneously move
both external adjustment levers upwards, to increase the stretch gradually and not
excessively (Fig.11).
The maximum stretch is achieved when the pin adjustment external levers are turned
outwards.
WARNING
- The presence of dust between the two visors may produce scratches on both
surfaces.
INSTRUCTIONS FOR USE