Nlynx OmniTerm WBT Скачать руководство пользователя страница 109

Страница: 109 / 131

Terminal Firmware Update

Upgrade Now Dialog Box

When you Click

“Upgrade Now!”

button, the confirm dialog box will

display.

When the upgrade procedure is finished, the system will ask to be restarted,
click Yes.

To complete update of the Windows CE Registry, press F2 at the Session
Manager screen, select the

General

Tab, ch

eck Reset the terminal to

factory-default settings

, then press Enter. The terminal will re-boot. You

can begin to use the terminal; or reset to defaults again (required when going
from CE2.0 to CE3.0).

Auto Upgrade/Configuration initiated via custom DHCP tags

(See

Appendix B):

The OmniTerm may be automatically updated/configured if you configure DHCP
to pass custom tags to the client. When powered on, this will occur when a newer
version is detected. To use this feature, in

Network Properties

insure that

Obtain an IP address from a DHCP server

is enabled and that all FTP options

are enabled under

Advanced DHCP

. The DHCP options must be setup as

described in Appendix B.

Upgrade Firmware Dialog Box

Click

Yes

to reboot WBT for upgrade or wait for timeout.

106

Содержание OmniTerm WBT




































































































































Результаты поиска

Содержание OmniTerm WBT

Отзывы:

Похожие инструкции для OmniTerm WBT

Бренды по названию

Популярные бренды

Nlynx OmniTerm WBT, Руководство пользователя

Результаты поиска

Содержание OmniTerm WBT

Отзывы:

Похожие инструкции для OmniTerm WBT

Бренды по названию

Популярные бренды