background image

5

when performing an operation where the cutting 

accessory may contact hidden wiring.  Cutting 

accessory contacting a “live” wire may make 

exposed metal parts of the power tool “live” and 

could give the operator an electric shock.

Drill safety warnings

 - Wear ear protectors when impact drilling.

   Exposure to noise can cause hearing loss.

 - Use auxiliary handle(s), if supplied with the tool.

  Loss of control can cause personal injury.

G E N E R A L  S A F E T Y  R U L E S  F O R 
CORDLESS MACHINE

WARNING

 

Do not use the battery pack other than for the 

cordless machine of Nitto.

  Use the battery charger and battery pack speci

fi

ed 

by Nitto described in the instruction manual and 

catalog. Use of a battery pack not speci

fi

ed by Nitto 

may cause machine failure, injury or damage.

 

Do not use deteriorated battery pack.

  Use of deteriorated battery pack may cause liquid 

leak, heat generation or explosion of the battery.

 

Use proper method for charging.

  Use a power source appropriate for the rated 

voltage of the battery charger. Do not use power 

source of direct current or engine generator. It may 

cause failure or 

fi

re.

  D o   n o t   c h a r g e   t h e   b a t t e r y   p a c k   w h e n   t h e 

temperature is less than 0°C or over 40°C. It may 

cause explosion or 

fi

re.

  Charge the battery pack at a well-ventilated area. 

Do not cover the battery pack or battery charger with 

a cloth, etc. It may cause explosion, smoke or 

fi

re.

  When not in use, unplug the power supply plug of 

the battery charger from the electric outlet. Leaving 

the machine plugged may cause electric shock, 

smoke or 

fi

re.

 

Do not use or charge at an area where there is 

fl

ammable liquid or gas.

  It may cause smoke, ignition or explosion.

 

Do not use or charge in rain or at damp or wet 

areas.

  It may cause electric shock or smoke.

 

Do not short circuit between terminals of the 

battery pack.

  Short circuit by water, cutting chips and other 

conductive materials may cause smoke, ignition or 

explosion.

 

Be careful of electric shock.

  Do not touch the power supply plug, terminals or 

their peripheral areas of the battery pack and battery 

charger with wet hands. It may cause electric shock.

 

Turn the switch of the machine off and disconnect 

the battery pack from the machine in cases 

described below.

  When not in use or when repairing.

  When replacing accessories such as a drill.

  When work is 

fi

nished and storing the machine.

  When other dangerous situation is assumed.

 

Avoid abrupt starting.

  Check that the switch is turned off before attaching 

the battery pack. Do not touch the arbor or drill when 

attaching the battery pack.

 

Use speci

fi

ed accessories and attachments.

  Use specified accessories and attachments 

described in this instruction manual and Nitto 

catalog. Use of other accessories and attachments 

may cause an accident or injury.

 

Do not place the battery pack in 

fi

re.

  It may cause ignition or explosion.

 

If the liquid of the battery pack leaks and gets into 

your eyes, do not rub your eyes but immediately 

wash your eyes with plenty of clean water such 

as tap water and consult with a medical doctor.

 

If the liquid of the battery pack leaks and comes 

in t o  c o n t a c t  w i t h  y o ur  s k in  o r  c l o t hin g, 

immediately wash with plenty of clean water and 

consult with a medical doctor since it may cause 

skin infection or injury.

 

Pay attention that the battery pack is clean from 

chips and dust.

  Prevent chips to fall on the battery pack when 

working.

  Do not leave the battery pack where chips or dust 

accumulate when the battery pack is not in use.

  Clean off chips and dust when storing the battery 

pack and store it separately from metal parts.

  Do not stick a nail or apply strong impact to the 

battery pack.

 

Do not apply heat or high pressure to the battery 

pack  by  putting it in a microwave  or  in a 

pressurized container.

 

Immediately move the battery pack away from 

fi

re 

when any leaking or smell is identi

fi

ed.

 

Do not use the battery pack for other devices.

 

Stop charging the battery pack when charging is 

not completed even after the specified charging 

time is signi

fi

cantly exceeded.

 

Do not use the battery pack that has external 

damage or signi

fi

cant deformation.

 

Do not use at areas where strong static electricity 

is generated.

15.+/2+..]AJ?+050.]C,glbb3

/2,7,/.28.582/NK

Содержание ATRA ACE CLA-2720



























Отзывы: