Nilfisk-Advance 56397010 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 55

background image

6 - FORM NO. 56043056 / ConvertaMAX™ 20/26 / BA 550/650

MAINTENANCE

MAINTENANCE SCHEDULE

Maintenance intervals given are for average operating conditions. Machines used in severe operational environments may require
service more often.

MAINTENANCE ITEM

Daily

Weekly

Monthly

Yearly

Charge Batteries

•

Drain/Clean and Check Tanks & Hoses

•

Check/Clean/Rotate the Brushes/Pads

•

Check/Clean/Adjust the Squeegee

•

•

Check/Clean Vacuum Shut-Off Float

•

Check Each Battery Cell(s) Water Level

•

Inspect and Clean Solution Filter

•

Lubrication – Grease Fittings

•

*Check Motor Carbon Brushes

•

Note: See the individual machine system sections for maintenance information.
* Have Nilfisk-Advance:

IMPORTANT!

Motor damage resulting from failure to service the carbon brushes is not covered under warranty. See the Limited Warranty
Statement.

Check vacuum motor carbon brushes (Qty 2) once a year or after 300 operating hours.
Note if the vacuum or brush motor carbon brushes are 9.5mm (3/8 inches) or shorter, replace them.

Check brush motor carbon brushes (Qty 4) once a year or after 500 operating hours.
Check wheel drive motor carbon brushes every 500 operating hours. The original length of each brush is 20mm (25/32 inches).
Replace when shorter than 9.5 mm (3/8 inches) to obtain the same motor efficiency as a new brush.

WARNING!

Turn the key switch off and disconnect the battery before servicing the machine.

BATTERIES AND CHARGERS

Attention: See the electrical system manual section for battery installation and charger system requirements.

LUBRICATING THE MACHINE

Once a month, pump a small amount of grease into each grease fitting on the machine until grease seeps out around the bearings.

Grease fitting locations are:
•

Rear Caster Wheel Axle & Swivel (2) per Assembly

Once a month, apply light machine oil to lubricate the:
•

Drive Chain

•

Squeegee Height Adjustment Caster Hardware

•

Pivot Points For the Squeegee & Scrub Brush Linkage

«
...
5
6
7
8
9
...
»

Содержание 56397010
























































Отзывы:

Нет отзывов

Похожие инструкции для 56397010

Бренд: Canon Страницы: 100

Бренд: Canon Страницы: 124

Бренд: Canon Страницы: 203

Бренд: Canon Страницы: 28

Бренд: Toyota Страницы: 39

Бренд: Jack Страницы: 61

Бренд: EVA Страницы: 56

MicroFogger 3 Pro

Бренд: Inventys Страницы: 13

BARRACUDA 200ZW

Бренд: Reliable Страницы: 40

Бренд: GBC Страницы: 74

MEMORYCRAFT 300E

Бренд: Janome Страницы: 48

Бренд: Nobles Страницы: 69

Бренд: Lavor Страницы: 10

Бренд: Olivetti Страницы: 16

Бренд: Siruba Страницы: 46

Бренд: Brother Страницы: 262

Бренд: Koblenz Страницы: 16

KENMORE 385. 1254180

Бренд: Kenmore Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды