Nilfisk-Advance 56397010 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 55

background image

FORM NO. 56043056 ConvertaMAX™ 20/26 / BA 550/650 - 39

WHEEL DRIVE SYSTEM

FRONT

Chain

Drive Wheel

Drive Wheel Motor

R1 Potentiometer

(25,000 Ohms)

R2 Potentiometer

(5,000 Ohms)

WHEEL DRIVE TROUBLESHOOTING GUIDE

Problem

Possible Cause

• No forward or reverse wheel drive.

See Electrical Troubleshooting Flowcharts A & B.

• No wheel drive in one direction,

Controller can’t change electrical polarity to wheel motor.

loss of either forward or reverse.

Replace the (A1) speed control.

• Machine creeps (moves) in forward or

• Check movement of the drive paddle spring centering device

reverse with only the key switch ON.

(auto dead-man return to neutral components). Repair or replace
needed parts.

• The R2 drive pot is out of adjustment. Reset to neutral the 5000
Ohm drive paddle potentiometer (*).

• During normal machine transporting with the 5K

The R1 (25,000 Ohm) speed limiting pot wiper is either open

drive paddle pot activated the operator also adjusts

where the machine runs at minimum speed or the pot wiper

the control panel maximum speed limiting R1 pot and

is shorted and runs at maximum speed. Replace the R1 pot (**).

does not affect the desired maximum machine speed
output.

* See

Potentiometer Installation and Adjustment

instructions in this manual section and reset the (5K) pot to neutral.

** See

25K Wheel Drive Speed Limit Potentiometer Testing

instructions in this manual section.

FIGURE 3

revised 9/01

«
...
38
39
40
41
42
...
»

Содержание 56397010
























































Отзывы:

Нет отзывов

Похожие инструкции для 56397010

PIXMA MX882 Series

Бренд: Canon Страницы: 80

MultiPASS C3500

Бренд: Canon Страницы: 47

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 212

HQ Sweet Sixteen

Бренд: Handiquilter Страницы: 41

Бренд: handi quilter Страницы: 2

Memory Craft 6300P

Бренд: Janome Страницы: 69

Бренд: Janome Страницы: 6

Бренд: Windsor Страницы: 22

Бренд: GBC Страницы: 43

Бренд: R+M Suttner Страницы: 4

Бренд: Ultratec Страницы: 11

WRANGLER 1503 AB

Бренд: NSS Страницы: 176

WRANGLER 2016 AE

Бренд: NSS Страницы: 20

Europa Style NM 600

Бренд: EST Страницы: 10

Bona PowerDrive

Бренд: Kunzle & Tasin Страницы: 2

Бренд: Horizon Fitness Страницы: 57

56263501 Aquamatic Selectric

Бренд: Nilfisk-Advance Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды