nilan Comfort CT300 Polar Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 15

nilan Comfort CT300 Polar Скачать руководство пользователя страница 9

Nilan reserves the right to alter these instructions without prior notice

Page 9 af 15

Heating surface, water



Connecting the heating surface must be done by an authorized plumber.

Heating surface for Comfort CT300 is a surface that should be installed in the ducting.

The heating unit is delivered as accessory and consists of heating surface with temperature sensor
T9 and frost-protection B3, actuator and regulating valve.

The heating surface should be connected, scavenged and checked for any leakages before start-
ing the unit.
The dirt-catcher should be checked and cleaned after a thoroughly flushing of the system.

Air flow

Flow

Return

B3

T9

2

1

M

Heating surface

3

Note that the temperature sensor T9 and frost-protection B3 is placed at the heated side of the heating
surface close to the return connection. See electrical chart.

1:

Actuator and regulating valve:
Danfoss AME 140/24V 0-10V signal, 2-way valve VZ2 Kvs 0,4, (Nilan delivery) Kvs-value must be
checked in accordance with supply.
Differential pressure: 0,1

– 0,6 bar

There is calculated with a cooling of 20°C over the heating surface at a flow of 60°C.

2:

Scavenging (not Nilan delivery)

3:

Dirt-catcher (not Nilan delivery)

Figure 5: Connecting the heating surface, suggestion

«
...
7
8
9
10
11
...
»

Содержание Comfort CT300 Polar
















Отзывы:

Нет отзывов