nilan Comfort CT300 Polar Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 15

nilan Comfort CT300 Polar Скачать руководство пользователя страница 5

Nilan reserves the right to alter these instructions without prior notice

Page 5 af 15

Assembly of Comfort



When mounting the Comfort-unit future service and maintenance should be considered.
For the Comfort CT300 a free place of minimum 60 cm in front of the system and 20 cm
below the system is recommended. The CT300 can be mounted directly on the wall.

In order to ease the mounting each of the connection pieces is labeled. Please notice the labels.
The connection between the unit and the ducting should be a flexible transition.

The  system must  be  level  because  of the  condense  outlet. The condense  outlet  requires  a  mini-
mum clearance height of 11,5 cm beneath the outlet connection.

The  exchanger  is  low-noise  and  low-vibration.  However,  potential  vibrations  spreading  from  the
system to the individual building parts must be taken into account. To detach the system from the
floor,  we  recommend  that  the  system  is  placed  on  vibration  absorbers.  The  vibration  absorbers
must  be  placed  diagonally  on  each  corner  to  ensure  that  the  system  does  not  “fall  down”  from
them.

It is not necessary to re-insulate the system as it is delivered with a 20 mm standard insulation.

1 cm

Comfort

Top

4

∼

Comfort

300 /450 / 600

vibration absorbers

Figure 2: Mounting the Comfort unit

«
...
3
4
5
6
7
...
»

Содержание Comfort CT300 Polar
















Отзывы:

Нет отзывов