nilan Comfort CT300 Polar Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 15

nilan Comfort CT300 Polar Скачать руководство пользователя страница 12

Nilan reserves the right to alter these instructions without prior notice

Page 12 af 15

Heating surface, electrical (retrofitting)

The heating surface should be installed in the inlet duct immediately after the unit.
There should be a safety distance of minimum 150mm from the heating surface to any flammable
materials. The heating surface must be insulated with a fire resistant material. However the electri-
cal box may not be insulated. (Important: instructions from the manufacturer of the heating surface
must be followed).

See electrical chart.

The heating coil is fitted with temperature limiter and safety thermostat state. Here is short-circuited
terminals 3 & 4 of CN6. When installing other hot surfaces should be thought carefully about the
safety of these. Heating coil must be equipped with temperature limiter and safety thermostat.

CV

230 V

Signal for overheatning

Unit

Intet

T7

The heating surface must be activated in the CTS 700 control panel.

«
...
10
11
12
13
14
...
»

Содержание Comfort CT300 Polar
















Отзывы:

Нет отзывов