nilan Comfort CT300 Polar Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 15

nilan Comfort CT300 Polar Скачать руководство пользователя страница 3

Nilan reserves the right to alter these instructions without prior notice

Page 3 af 15

Introduction



Please control that the following documents have been delivered together with the unit:

-

Directions for assembly & use (this document)

-

CTS 700 user guide

-

Electrical chart

Should you have any questions on how to operate the system, contact your nearest Nilan dealer,
who you can find at

www.nilan.dk/dealers

The purpose of this instruction manual is to offer the installation contractor and the user instruc-
tions on correct installation and maintenance of the Comfort system.

Comfort is a ventilation unit with heat recovery. The unit can yield up to 400m

3

/h at 100Pa external

back pressures. The energy in the exhaust air is being transferred to the inlet air.

The system is prepared for retrofitting of a post-heating element (electricity or water) for supply
heating of the inlet air. The post-heating element is controlled via CTS 700.

The unit is delivered with a G4 filter. In addition to this the unit can be equipped with different ac-
cessories e.g. hygrostat and filter box with pollen filter.

The  plant  has  to  be  started  immediately  after  installation  and  connection  to  the  canal  system.
When a ventilation plant is not running, the moist air from the rooms will be able to penetrate into
the channels and systems and allocate condensation. Condensation can run out of the valves and
damage  furniture  and  floors.  Condensed  water  in  the  plant  may  damage  the  electronics  and  the
fans.

Operating the unit is done with the CTS 700 control. The control has many functions such as menu
based attendance, week programme, time controlled filter guard and adjustment of the velocity of
the ventilator. (Directions for the CTS 700 control is described in another document delivered with
the unit.)

Comfort is delivered tested and ready for use. Installation and start-up must be carried out by an
authorized electrician.

«
1
2
3
4
5
...
»

Содержание Comfort CT300 Polar
















Отзывы:

Нет отзывов