Nikon JAA79551 Скачать руководство пользователя страница 80

Страница: 80 / 115

INC

JAA79551-R.3690.A

- Ａ 53・AF-S VR 70-300/4.5-5.6G -

Buttons for adjustment

at 90 ° position

　・

After the adjustment, click the [Rewrite] button to write the adjustment value in EEPROM in the lens.

　・

Then, click the [EXIT] button to evacuate from the adjustment mode.

Notes：

If clicking [EXIT] button after not clicking the [Rewrite] button, the adjustment value is not stored

and the adjustment is not influenced.

　・

Click the [Quit] button at the Adjustment Items window to go back to the Lens Selection window.

Notes：

Do not remove the lens or turn OFF the VR lens adjustment equipment until it goes back to the

Lens Selection window. The trouble that the adjustment value is not stored correctly, etc. occurs since

the communication is cut off.

・

Press "STOP" button of VIBRATION switch of the VR

adjustment equipment to stop vibrations.

・

Rotate the lens through 90° in the direction indicated by the

arrow, then press “START” button of VIBRATION switch

to start vibrations.

・

At the 90° position, adjust the angle misalignment and

make gyro-gain adjustment.

Note

: When adjusting the lens at the 90 ° position, adjust by

the buttons for the adjustment at 90 ° position as shown

below.

Содержание JAA79551




















































































































Результаты поиска

Содержание JAA79551

Отзывы:

Похожие инструкции для JAA79551

Бренды по названию

Популярные бренды

Nikon JAA79551, Руководство по ремонту

Результаты поиска

Содержание JAA79551

Отзывы:

Похожие инструкции для JAA79551

Бренды по названию

Популярные бренды