Nikon JAA79551 Скачать руководство пользователя страница 39

Страница: 39 / 115

INC

JAA79551-R.3690.A

- Ａ・AF-S VR 70-300/4.5-5.6G -

(GND)

( ＋ )

・

How to inspect and adjust:

①

Confirm that the electric current and voltage of the connected rated voltage power-supply are set values, then

turn it ON.

②

Set the oscilloscope. �old "A" part of the SWM unit at three places firmly, and rotate the MR coupling ring

"A" part of the SWM unit at three places firmly, and rotate the MR coupling ring

with fingers.

Note: The waveform varies according to the rotational speed of the focus ring. So change "Time/Div”

setting accordingly.

Be careful NOT to touch the metal area of

the SWM unit.

Metal area

A part

MF coupling ring

GMR sensor FPC

● When the MR head is disassembled and replaced,

be sure to make an adjustment.

1. Device:

　　・

Single-output rated voltage power-supply

1 unit: 5V 100mA

　　・

Oscilloscope

1 unit

　　・

Self-made tool 1 unit

Caution:

If there is a problem with continuity between the contacts of the self-made tool and the relay FPC,

the contacting surface of the relay FPC may be dirty, eroded, or oxidized. So polish the contacts and

connect them.

2. Preparation of the lens for measurement

　　・

Assemble the MR-head-attached zoom index ring unit, the SWM, and the MF ring into the lens body.

Then connect the assembled lens to each measuring machines as follows:

Inspection and adjustment of output waveform of MR encoder

・

【

Attachment diagram

】

PCB (Back)

PCB (Front)

To back side

Caution:

The connector of the back of

the PCB is not used.

Oscilloscope (2ch)

Oscilloscope (1ch)

Rated voltage power-supply (+)

Rated voltage power-supply (-)

Rated voltage power-supply

Set value

5.0 V

100 mA

Oscilloscope

(2ch type)

Self-made tool

Содержание JAA79551




















































































































Результаты поиска

Содержание JAA79551

Отзывы:

Похожие инструкции для JAA79551

Бренды по названию

Популярные бренды

Nikon JAA79551, Руководство по ремонту

Результаты поиска

Содержание JAA79551

Отзывы:

Похожие инструкции для JAA79551

Бренды по названию

Популярные бренды