Nikon JAA79551 Скачать руководство пользователя страница 78

Страница: 78 / 115

INC

JAA79551-R.3690.A

- Ａ 51・AF-S VR 70-300/4.5-5.6G -

・

Angle Difference Adjustment

If there is angle difference, the laser beam source
becomes be whether if it rotates round even performing

the Gyro Gain Adjustment.
If it is possible to confirm the angle difference, adjust it
by the buttons for the angle difference adjustment.

Notes：

After operating the adjustment button, wait for

a few seconds until a vibration motion is stabilized.

Buttons for [Gyro

Gain] Adjustment

Buttons for [Angle
Difference] Adjustment

・

Gyro Gain Adjustment

Adjust the vibration width by the button for Gyro Gain Adjustment so that the length of the vibration width

becomes be less than 1/5 of the measured laser vibration width a.

Standard: Less than 1/5 of the vibration width a

Notes：

The laser beam vibrates widely again after it

passes the peak section of the minimum value.

Peak section of the minimum
value of the vibration width

Содержание JAA79551




















































































































Результаты поиска

Содержание JAA79551

Отзывы:

Похожие инструкции для JAA79551

Бренды по названию

Популярные бренды

Nikon JAA79551, Руководство по ремонту

Результаты поиска

Содержание JAA79551

Отзывы:

Похожие инструкции для JAA79551

Бренды по названию

Популярные бренды