Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Скачать руководство пользователя страница 73

Страница: 73 / 93

JAA80151-R.3718.A

Ａ 4・AF-S 4-24/2.8G

Tick here except when the lens is positioned horizontally.

・

Make inspections by focal length 14mm (W) or 24m (T)

at the following five lens positions.

(3) Inspection screen of lens driving stop accuracy

・

If the lens stops while inspecting the lens driving stop accuracy, input a figure in "Delay time" entry

field of the below "Fig.2", from "0" to "1000" for the delay time (msec: millisecond) which prevents

stopping the lens.

Note:

The value of "ADUST DELAY-TIME" is set by the adjustment software. So, as far as the lens does not

stop during the inspection of "LENS DRIVING STOP ACCURACY", any value can be input without

problem.

However, the larger the value of "ADJUST DELAY-TIME" gets, the longer the inspection time becomes.

(Lens position in inspecting)

Horizontal lens position

Index

90° angle rightward (from horizontal position)

Index

90° angle leftward ( ditto )

Front lens group 90° angle upward ( ditto )

Front lens group 90° angle downward ( ditto )

INC

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Руководство по ремонту

Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды