Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Скачать руководство пользователя страница 30

Страница: 30 / 93

JAA80151-R.3718.A

- Ａ・AF-S 4-24/2.8G -

Cam tube

Positioning of Inner fixed tube and Cam tube

Attach the three 1st lens-G keys with six screws

(#72) temporarily.

The 1st lens-G key must be selected from A to C, according to the groove width.

�
�

1st lens-G key ×3

#72×6

Inner fixed tube

Cam tube

1st lens-G key×3

Direction for positioning

Position the inner fixed tube and cam tube in the direction of the arrow, and tighten six screws (#72).

#72×6

Cam tube

Adhesive: Lockend B

Facing direction of 1st lens-G key

Caution:

When positioning, confirm that there is no irregularity or backlash by moving the cam tube

back and forth several times.

Groove

width

INC

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Руководство по ремонту

Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды