Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Скачать руководство пользователя страница 31

Страница: 31 / 93

JAA80151-R.3718.A

- Ａ・AF-S 1-2/2.8G -

April��2��8

��2��8

�2��8

2��8

Temporary attachment of 1st lens-G lead key

1st lens-G lead ring

Inner fixed

tube

1st lens-G lead ring

Inner fixed tube

1st len-G lead key×3

#191×6

Grease: GN-20S

Cam groove ×3 and

Inside lead ring groove ×3

Oil barrier: OS-30MEL

Apply to G2 lens attaching surface

Rotate the cam tube, and set the zoom key groove to the rightmost position.

Attach the 1st lens-G lead ring to the inner fixed tube.

Cam tube

Zoom key groove

Attach three 1st lens-G lead keys to the mid-fixed tube with six screws (#191).

Select the 1st lens-G lead key from A or B to D

, which fits in the groove width of the 1st lens-G

lead ring without backlash.

�

Apply to

△ (Revision)

Changed page

△× 1

INC

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Руководство по ремонту

Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды