Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Скачать руководство пользователя страница 50

Страница: 50 / 93

JAA80151-R.3718.A

- Ａ 2・AF-S 4-24/2.8G -

Standard:

Amplitude of all pulses/waveforms is 180mV or more.

Note:

Check the waveform by rotating the focus turning-tube all the way around back and

forth.

●

Oscilloscope setting

V/Div (ch1)

: 100 mV

V/Div (ch2)

: 100 mV

Coupling

: AC

Time/Div

: 1ms

Trigger Mode

: NORMAL

Trigger Coupling

: AC

Trigger Source :

: CH1

Trigger Position

: + 4 div

Trigger Type

: EDGE

Trigger Level

: 0V

INPUT (ch1)

: AC

INPUT (ch2)

: AC

．

How to inspect and adjust:

・

Confirm that the electric current and voltage of the connected rated voltage power-supply are set

values, then turn it ON.

・

Set the oscilloscope, and turn the focus turning-tube with hand.

・

In case large waveform-noise is detected, use the FILTER function.

How to set FILTER function (e.g. DL1540 manufactured by YOKOGAWA

）

1. Press the FILTER button.

2. Select “Smooth” of the menu on screen and turn it ON.

CH1

CH2

1ms/div
NORM:1MS/s

CH1=100mV
AC 10:1

CH2=100mV
AC 10:1

DT 1.13MS

In case the amplitude is small, adjust by loosening the two screws (#119) and moving the GMR sensor.

Caution: Do NOT touch the sensor area directly with hands during adjusting.

Sensor area

#119×2

INC

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Руководство по ремонту

Результаты поиска

Содержание AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Отзывы:

Похожие инструкции для AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Бренды по названию

Популярные бренды