EN
5.6 - Setting force on closure: “RDC” function
Caution!
- The “RDC” level can only be personalised after programming the limit positions “0” and “1”, using the Semi-automatic procedure (paragraph 5.5).
01.
Use the
Up
or
Down
button to move the awning to the point of mid-travel.
02.
Press and hold the
Up
pushbutton until the aw ning reaches limit position “0” (do not release the button).
03.
Then, with the
Ascent
button still pressed, press the
Descent
button the number of times as the level to be selected (press each time for 1 second, with a pause
of 1 second before pressing again). With the
Up
button still pressed, wait until the awning completes the same number of movements (in the down direction) as
the new level set. The levels available are:
level 1
= maximum force (
factory setting.
) /
level 2
= medium force /
level 3
= minimum force
04.
Then release the
Up
button.
x 1
= forza massima /
x 2
= forza media /
x 3
= forza minima /
04
02
01
03
1
/
2
/
3
THE
END
“
0
”
?
x 1
= maximum force /
x 2
= medium force /
x 3
= medium force /
English –
4
5.7 - Deleting the entire memory
Caution!
- This procedure deletes all data in the Con trol unit memory, including positions “0” and “1”.
01.
Use the
Up
or
Down
button to move the awning to the point of mid-travel.
02.
Press and hold the
Up
and
Down
buttons simultaneously and wait for the awning to perform a short movement (
note
– if the awning makes two short move-
ments, continue the procedure in any case); after which release only one of the two buttons.
03.
With 3 seconds after the awning has performed the short movement, press the previously released button (in point 02) three times.
04.
The release the other pushbutton.
02
01
x
3
03
04
THE
END
1
EC declaration of conformity
Nice S.p.A. hereby declares that the products:
Neo Tandem 2 x 80 / 12, Neo Tandem 2 x 100 / 12, Neo Tandem 2 x 120 / 12
comply with the essential requirements
and other relevant provisions as established by the directives
2006/95/EC
,
2004/108/EC
. The EC declaration of conformity can be consulted and printed out at the web
site www.nice-ser vice.it or may be requested from Nice S.p.A.
Ing.
Luigi Paro
(Managing Director)
Power supply voltage:
see specifications on the motor dataplate
Power absorption on standby:
0,5 W
Encoder resolution:
2,7°
Continuous operation time:
4 min
Operating temperature:
-20°C
IP Protection rating:
IP 44
Note
:
– All technical characteristics refer to an ambient temperature of 20°C (± 5°C).
– Nice S.p.a. reserves the right to apply modifications to the product at any ti me
when deemed necessary, while maintaining the same functionalities and in tended
use.
Technical specifications
Disposal of the product
This product constitutes an integral part of the automation system, therefore it
must be disposed of along with it.
As in installation, also at the end of product lifetime, the disassembly and scrapping
operations must be performed by qualified personnel.
This product is made up of different types of material, some of which can be recycled
while others must be disposed of. Seek information on the recycling and disposal
systems envisaged by the local regulations in your area for this product category.
Caution!
- some parts of the product may contain pollutant or hazardous sub-
stances which, if disposed of into the environment, may cause serious
damage to the environment or physical health. As indicated by the
symbol on the left, disposal of this product in domestic waste is strictly
prohibited. Separate the waste into categories for disposal, ac cording
to the methods envisaged by current legislation in your area, or return
the product to the retailer when purchasing a new version.
Caution!
- Local legisla-
tion may envisage serious fines in the event of abusive disposal of this product.
