background image

The composition and use of the system involve aspects that impact 

consumption, in particular the brightness of the display, the power 

draw of sirens and of any peripherals wired to the system. These 

factors must be taken into account in relation to the power supply’s 

power rating, which must be able to guarantee correct charging of all 

the connected batteries. The table indicates the current draw levels 

of the 3 control unit models and the relative batteries. For each sys-

tem the following elements must be calculated:

a)

 the maximum current draw, calculated by adding to the con-

sumption of the control unit that of other devices wired to it, must 

not exceed the power supply’s capacity (the current draw should be 

contained to 80% of the nominal capacity).

b) 

the minimum autonomy, in the absence of 230 V power supply, 

taking into account 80% of the battery’s nominal capacity.

Warning!

 If there is no mains power, the display and Wi-Fi module of 

the control unit will be disabled. Connection to the network must be 

made through the GSM/GPRS module.

Warning!

 Control units with touch screen (MNCUT/MNCUTC): take 

into account the indicated consumption differences, linked to the 

brightness of the touch screen – good visibility can be obtained even 

at 35%.

Technical characteristics

Current draw

Table 1

Code

MNCUT

MNCUTC

MNCUC

Power supply

110 V–240 V

110 V–240 V

110 V–240 V

Surveillance

18’

18’

18’

Radio transmission

GFSK dual band 433.54-

433.92 MHz; 868.30-

868.94 MHz

GFSK dual band 433.54-

433.92 MHz; 868.30-

868.94 MHz

GFSK dual band 433.54-

433.92 MHz; 868.30-

868.94 MHz

Open-field radio range,  

without disturbances

> 100 m

> 100 m

> 100 m

Insulation (class)

II

II

II

Environmental class 

 in accordance with EN 50131-1

2

2

2

Operating temperature

–10°C ... +40°C

–10°C ... +40°C

–10°C ... +40°C

Dimensions (WxDxH)

265 x 265 x 40 mm

265 x 265 x 85 mm

265 x 265 x 85 mm

Weight

1,250 g

1,850 g

1,650 g

IP

40

40

40

Table 2

Code

MNCUT MNCUTC MNCUT MNCUTC MNCUT MNCUTC MNCUT MNCUTC MNCUTC and MNCUC

MNCUT

Power supply 

110–240V

110–240V

BLACK-OUT

BLACK-OUT

Touch screen bright-

ness

100%

50%

10%

-

-

-

Mains power

7.5 V

2 A

14.5 V

1.6 A

7.5 V

2 A

14.5 V

1.6 A

7.5 V

2 A

14.5 V

2 A

14.5 V 

1.6 A

7.5 V 

2 A

-

-

Battery pack

1 x 6 V 

1.2 Ah

1–2 x 12 V 

2.2 Ah

1 x 6 V  

1.2 Ah

1–2 x 12 V 

2.2 Ah

1 x 6 V  

1.2 Ah

1–2 x 12 V 

2.2 Ah

1–2 x 12 V 

2.2 Ah

1 x 6 V 

1.2 Ah

1–2 x 12 V 

2.7 Ah

1 x 6 V 

1.2 Ah

Current draw in stand-by
CPU 

(mA)

720

390

520

300

350

200

150

270

30

45

Wi-Fi 

(mA)

40

40

40

40

40

40

40

40

-

-

Circuit board 

(mA)

-

20

-

20

-

20

20

-

20

-

MNGSM 

(mA)

10

10

10

10

10

10

10

10

10

10

MNPSTN 

(mA)

0

0

0

0

0

0

0

0

0

0

Total 

(mA)

770

460

570

370

400

270

220

320

60

55

5

Содержание MNCUC





















Отзывы: