NewMar SilverLeaf RV-C Control System Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 67

background image

Page 7

DC POWER SCREENS MAGNUM STATUS SCREEN

The DC Power (Settings) Magnum Status Screen
displays the following Status Values:

Magnum Model/Version

This value is read from the inverter via the
Inverter Module.

Battery Temperature

This value is read from the inverter battery
temperature sensor via the Inverter Module.

Internal Temperature

This value is read from the inverter via the
inverter Module.

FET Temperature

This value is read from the inverter via the
Inverter Module.

DC POWER SCREENS MAGNUM ADVANCED SETTINGS SCREEN ACCESS

The Password Access Screen is displayed to
provide access to advanced system
configuration screens. The advanced
configuration screens contain control settings
that should only be changed by qualified
individuals. Changing these control settings to
an improper setting can adversely affect the
operation of the control system and may cause
damage to the coach.

DC POWER SCREENS MAGNUM ADVANCED SETTINGS SCREEN 1

The Magnum Advanced Settings Screen has the
following Configuration Values:

Low Voltage Shutdown ( DC Voltage)

This setting is the low DC Voltage trigger point
that will turn off the Inverter.

Battery Type Flooded / Gel /
AGM / AGM2

This should be set to match the physical
battery type.

Battery Rating

(AH)

This should be set to match total house
battery power capacity

Equalization Volts

( DC Voltage)

This setting should match the manufacturer
setting for the battery type.

«
...
7
8
9
10
11
...
»

Содержание SilverLeaf RV-C Control System




































































Отзывы:

Нет отзывов

Похожие инструкции для SilverLeaf RV-C Control System

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: Laars Страницы: 28

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

Бренд: WEST Страницы: 2

VEGACAP 60 Series

Бренд: Vega Страницы: 12

Бренд: D+H Страницы: 17

Бренд: LAUNDRY SOLUTION Страницы: 14

Бренд: ICP DAS USA Страницы: 8

Бренд: WAGO Страницы: 50

Бренд: V2 Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды