NewMar SilverLeaf RV-C Control System Скачать руководство пользователя страница 22

Страница: 22 / 67

Page 20

FEATURES MONITOR CONFIGURATION SCREEN 6

The sixth Monitor Configuration Screen is
accessed by pressing the Next Button located
on the fifth Monitor Configuration Screen or

from the “Prev” Button located on seventh
Monitor Configuration Screen. This Screen
allows you to set the following Display Settings:

Transfer Switch Type

Set to “Generic”

(Automatic if RV-C Communications Port Used)

Select using the Up / Down Arrows

Inverter Model

Set to “Basic Magnum”

Select using the Up / Down Arrows

Floor Heat Mats

Set to “0” if no Floor

Heat Installed / Set to “3” if Floor Heat Installed

Select using the Up / Down Arrows

Floor Heat Schedule

(None, 2 Time Zone or 4

Time Zone)

Select Appropriate Setting using the Up /
Down Arrows

FEATURES MONITOR CONFIGURATION SCREEN 7

The seventh Monitor Configuration Screen is
accessed by pressing the Next Button located

on the sixth Monitor Configuration Screen or
from the “Prev” Button located on eighth
Monitor Configuration Screen.
This Screen allows you to set the following:

Power management Installed Set to TM-250

Select using the Up / Down Arrows

Tile Heat System Installed

Set to TM-220

Timed – if Floor Heat is installed

Select using the Up / Down Arrows

Autotemp AGS Installed

Set to

Autotemp for Temperature Autogen Control

Select using the Up / Down Arrows

Block Heater Instance

Set to 1

Select using the Up / Down Arrows

Содержание SilverLeaf RV-C Control System




































































Результаты поиска

Содержание SilverLeaf RV-C Control System

Отзывы:

Похожие инструкции для SilverLeaf RV-C Control System

Бренды по названию

Популярные бренды

NewMar SilverLeaf RV-C Control System, Руководство по обучению

Результаты поиска

Содержание SilverLeaf RV-C Control System

Отзывы:

Похожие инструкции для SilverLeaf RV-C Control System

Бренды по названию

Популярные бренды