2 - SAFETY INFORMATION
whether tires are inflated or deflated. The tire MUST be
completely removed from the wheel or rim prior to weld-
ing the wheel or rim.
Driving on public roads and general
transportation safety
Comply with local laws and regulations.
Use appropriate lighting to meet local regulations.
Make sure that the SMV emblem is visible.
Make sure that the brake pedal latch is engaged. You
must lock brake pedals together for road travel.
Use safety chains for trailed equipment when safety
chains are provided with machine or equipment.
Lift implements and attachments high enough above
ground to prevent accidental contact with road.
When you transport equipment or a machine on a trans-
port trailer, make sure that it is properly secured. Be sure
the SMV on the equipment or machine is covered while
being transported on a trailer.
Be aware of overhead structures or power lines and make
sure that the machine and/or attachments can pass safely
under.
Travel speed should be such that you maintain complete
control and machine stability at all times.
Slow down and signal before turning.
Pull over to allow faster traffic to pass.
Follow correct towing procedure for equipment with or
without brakes.
Fire and explosion prevention
Fuel or oil that is leaked or spilled on hot surfaces or elec-
trical components can cause a fire.
Crop materials, trash, debris, bird nests, or flammable
material can ignite on hot surfaces.
Always have a fire extinguisher on or near the machine.
Make sure that the fire extinguisher(s) is maintained and
serviced according to the manufacturer’s instructions.
At least once each day and at the end of the day, remove
all trash and debris from the machine especially around
hot components such as the engine, transmission, ex-
haust, battery, etc. More frequent cleaning of your ma-
chine may be necessary depending on the operating en-
vironment and conditions.
At least once each day, remove debris accumulation
around moving components such as bearings, pulleys,
belts, gears, cleaning fans, etc. More frequent cleaning
of your machine may be necessary depending on the
operating environment and conditions.
Inspect the electrical system for loose connections and
frayed insulation. Repair or replace loose or damaged
parts.
Do not store oily rags or other flammable material on the
machine.
Do not weld or flame cut any items that contain flammable
material. Clean items thoroughly with non-flammable sol-
vents before welding or flame-cutting.
Do not expose the machine to flames, burning brush, or
explosives.
Promptly investigate any unusual smells or odors that
may occur during operation of the machine.
General battery safety
Always wear eye protection when you work with batteries.
Do not create sparks or have open flame near a battery.
Ventilate the area when you charge a battery or use a
battery in an enclosed area.
Disconnect the negative (-) terminal first and reconnect
the negative (-) terminal last.
When you weld on the machine, disconnect both termi-
nals of the battery.
Do not weld, grind, or smoke near a battery.
When you use auxiliary batteries or connect jumper ca-
bles to start the engine, use the procedure shown in the
operator’s manual. Do not short across terminals.
Follow the manufacturer’s instructions when you store
and handle batteries.
Battery post, terminals, and related accessories contain
lead and lead compounds. Wash hands after handling.
This is a California Proposition 65 warning.
Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes, or clothing. Antidote (exter-
nal): Flush with water. Antidote (eyes): flush with water
for 15 minutes and seek medical attention immediately.
Antidote (internal): Drink large quantities of water or milk.
Do not induce vomiting. Seek medical attention immedi-
ately.
Keep out of reach of children and other unauthorized per-
sons.
2-4
Содержание Workmaster 25 Tier 4B
