New Holland Haybine 499 Скачать руководство пользователя

Страница: 74 / 128

SECTION 4 - MAINTENANCE

4-14

REMOVING AND REPLACING KNIFE

ASSEMBLIES

WARNING

When removing or installing a knife assembly, do

not hold down the sections with fingers or any

short object that could slip and result in loss of,

or injury to, fingers.

Removal

To remove a knife assembly, remove knife head bolt,

1. A 13/16

″

socket fits the nut and a 3/4

″

wrench fits

the bolt head. The nut and bolt are tapered to fit

countersunk holes in the rocker arms, 2. Use an

extension and socket through hole, 3, to loosen the

connecting rod bolt, 4.

If the knife is hard to remove because guards or

knives are bent, loosen the guard bolts.

IMPORTANT:

The rubber bushings in the knife head

and connecting rod will last much longer if the knife

is moved to the center of its stroke before tightening

bolts, 1 and 4. The knife will be in center-stroke if a

socket wrench installed through frame hole, 3, lines

up with the connecting rod bolt, 4.

IMPORTANT:

Straighten the knife assembly if it is

bent.

Hold the knife head and sight along the knife back.

The knife must be straight. Rotate the knife 1/4 turn

and recheck for bends. To remove a bend, clamp the

knife back in a vise. Another way to remove a bend

is to lay the high spot on a tire or the frame. Press at

each side of the bend until the knife is straight. Do not

straighten the knife with a hammer as the knife back

may be damaged.

Riveted Knives

Check the knife assemblies for loose rivets. To

tighten a rivet; place the rivet over a solid support.

Strike the rivet with a heavy hammer to swell the rivet.

If several rivets are loose, it is usually easier to

remove the knife assembly and then reseat the

rivets.

10004739

Содержание Haybine 499

































































































































Результаты поиска

Содержание Haybine 499

Отзывы:

Похожие инструкции для Haybine 499

Бренды по названию

Популярные бренды

New Holland Haybine 499, Руководство оператора

Результаты поиска

Содержание Haybine 499

Отзывы:

Похожие инструкции для Haybine 499

Бренды по названию

Популярные бренды