Network Equipment Technologies SBC 2000 Скачать руководство пользователя страница 4

Страница: 4 / 38

1. Power Status LED
2. Alarms Status LED
3. Peer Node Status LED
4. Ready Status LED

For more information about the error states of these LEDs, see

1. Power Status LED

This status LED indicates the power conditions of the UX system. The normal state of this LED is on and green.

2. Alarms Status LED

This status LED indicates if there are any critical alarms active on the UX system. The normal state of this LED is off.

3. Peer Node Status LED

This status LED indicates if the UX system is participating in a peer relationship. The normal state of this LED is off.

4. Ready Status LED

This status LED indicates if the UX system is ready to process calls. The normal state of this LED is on and green.

UX Ethernet and USB Ports

This section describes the Ethernet and USB ports found on the front panel of your US system.

UX Ethernet and Management Ports

Ethernet Ports
Management Port

UX USB Ports
Survivable Branch Appliance (SBA) USB Ports

UX Ethernet and Management Ports

Ethernet Ports

Your UX comes equipped with either four or eight Gigabit Ethernet ports located near the center of the front panel. The ports are grouped in two sets,
ports 1 through 4 on the bottom and ports 5 through 8 on the top as shown below.

Содержание SBC 2000






































Результаты поиска

Содержание SBC 2000

Отзывы:

Бренды по названию

Популярные бренды

Network Equipment Technologies SBC 2000, Руководство пользователя

Результаты поиска

Содержание SBC 2000

Отзывы:

Бренды по названию

Популярные бренды