NetPing server room environmental monitoring solutions and IP power distribution units.
Copyright © NetPing east Co., Ltd / E-mail:
/ Phone: +886-2-23121582
[email protected] www.netpingdevice.com
Thermo: channel N "XXXX"
, below normal
YYC
(AA
)
..BBC – is recorded into the log file when readings of a temperature sensor are below the
limits of a range specified by a user
. N – is a number of a channel of a
when notifications from a temperature sensor are enabled in the log file
temperature sensor. XXXX – is a description of a temperature sensor, specified by a user at the page of a web interface. YY – are readings of a
current temperature in °C. AA – is a lower limit of a temperature range in °C. BB – is an upper limit of a temperature range in °C.
Thermo: channel N "XXXX" - there is no sensor or it is faulty – is recorded into the log file when a temperature sensor does not respond (is not
connected)
.
when notifications from a temperature sensor are enabled in the log file N – is a number of a channel of a temperature sensor. XXXX
– is a description of a temperature sensor, specified by a user at the page of a web interface.
EVENTS FROM A HUMIDITY SENSOR
Humidity XX%, normal (YY..ZZ%) – is recorded into the log file when readings of a humidity sensor are within the limits of a range specified by a
when notifications from a humidity sensor are enabled in the log file. XX – are readings of a relative humidity in %. YY is a lower limit of a
user
normal humidity in %. ZZ – is an upper limit of a normal humidity range in %.
Humidity XX%, above normal (YY..ZZ%) – is recorded into the log file when readings of a humidity sensor are above the limits of a range
specified by a user
. XX – are readings of a relative humidity in %. YY is a
when notifications from a humidity sensor are enabled in the log file
lower limit of a normal humidity range in
%. ZZ is an upper limit of a normal humidity range in %.
Humidity XX%, below normal (YY..ZZ%) – is recorded into the log file when readings of a humidity sensor are below the limits of the range
specified by a user
. XX – are readings of a relative humidity in %. YY – is a
when notifications from a humidity sensor are enabled in the log file
lower limit of a normal humidity range in
%. ZZ – is an upper limit of a normal humidity range in %.
Humidity - there is no sensor or it is faulty – is recorded in the log file when a humidity sensor does not respond (is not connected) when
.
notifications from a humidity sensor are enabled in the log file
EVENTS FROM SMOKE SENSORS
Smoke sensor N "XXXX" switched to the status "YYYY" – is recorded into the log file when a status of a smoke sensor is being changed when
notifications from a smoke sensor are enabled in the log file. X – is a channel number of a smoke sensor. XXXX is a description of a channel of a
smoke sensor, which is specified by a user at the page of a web interface. YYYY is a name of a current status of a smoke sensor. The next
statuses are possible: «Normal», «ALARM», «Off», «Failure».
EVENTS OF THE MODULE «WATCHDOG»
Watchdog: resetting a channel N "XXXX". A (IPA) YYYY, B (IPB) YYYY, C (IPC) YYYY – is recorded into the log file when the module Watchdog
«
. N – is a number of a power management channel. XXXX – is a description of a power management channel, which is specified by a
» is triggered
user at the page of a web interface. IPA, IPB, IPC – IP addresses specified by a user in the settings of the module «Watchdog» are substituted.
YYYY – is a status, corresponding to a requested IP address. The next statuses are possible:
,
,
.
«responds» «silent» «ignored»
Watchdog: channel N "XXXX" - a limit of repeated resets is over (Y). Resets are paused. – is recorded into the log file if in the mode of the module
«Watchdog» a limit for the number of consequent resets of a connected device is reached. N – is a number of a power management channel.
XXXX - is a description of a power management channel, specified by a user at the page of a web interface. Y – is a number of consequent resets
.
of a connected device
Watchdog: channel N "XXXX" reset - a response is received. Reset pause is over. – is recorded into the log file if a response from the module «W
resets are paused after a specified limit is reached.
atchdog» is received in the status when
«Wathdog» signals a reset of reboots and a start of a
.
normal functioning of the watchdog according to a usual algorithm
EVENTS OF THE MODULE «SCHEDULE»
Schedule N switched to the status YYYY – is recorded into the log file when the module
.
«Schedule» is triggered N is a number of a power
management channel. YYYY – is a status of an embedded relay. The next statuses are possible: on ,
.
«
» «off»
EVENTS FROM EMBEDDED RELAYS
PWR: relay N "XXXX" YYYY – is recorded into the log file when an embedded relay was triggered. N – is a number of a power management
channel. XXXX – is a description of a power management channel, specified by a user at the page of a web interface. YYYY is a status of an
embedded relay. The next statuses are possible:
,
.
«switched on» «switched off»
PWR: relay N "XXXX" is switched to the mode "YYYY" through the web interface – is recorded into the log file when a relay management mode is
through a
switched
device web interface. N – is a number of a power management channel. XXXX – is a description of a power management
channel, specified by a user at the page of a web interface. YYYY – is a name of a relay management mode. The next modes are possible: «switc
hed off manually ,
» «switched on manually ,
» «watchdog management ,
» «schedule management ,
» «schedule and watchdog management ,
» «logic
management .
»
PWR: relay N "XXXX" is switched to the mode "YYYY" through SNMP – is recorded into the log file when a relay management mode is switched
using an SNMP protocol. N – is a number of a power management channel. XXXX – is a description of a power management channel, specified
by a user at the page of a web interface. YYYY – is a name of a relay management mode. The next modes are possible: «switched off manually»,
«switched on manually», «watchdog management», «schedule management», «schedule and watchdog management», «logic management».
PWR: relay N "XXXX"
"YYYY" by running
is switched to the mode
cgi – is recorded into the log file when
u
a relay management mode is switched
sing URL-encoded commands (HTTP API). N – is a number of a power management channel. XXXX is a description of a power management
channel, specified by a user at the page of a web interface. YYYY –
is a name of a relay management mode. The next modes are possible:
