Net Insight Nimbra 300 Series Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 100

background image

72

•

DTM Configuration

Element Manager User’s Manual Nimbra OneSerie

©2006 Net Insight AB, All rights reserved

DTM Configuration

Overview of DTM configuration

This chapter describes how to use the web interface to configure monitor the
DTM-layer. The start web page for DTM is shown in the, Figure 64, below.

Figure 64. The start web page for DTM

The sub-sections are:

•

Interfaces: monitor the state of the DTM interfaces and configure the
interfaces present in the unit.

•

Addresses: configure the DTM addresses of the unit.

•

Host names: configure mapping between the host names and the DTM
addresses.

•

Links: show the state of the DTM links to other units. The page can be
used to check if the links to the surrounding nodes have been properly
established.

•

Routing: monitors and configures the DTM routing.

•

Sync: monitor the synchronization status of the node and modify the
external clock.

Note:

Make sure to have all the information that the operation
requires, before starting any configuration operationThis will
help you to minimize any downtime of the system.

«
...
72
73
74
75
76
...
»

Содержание Nimbra 300 Series





































































































Отзывы:

Нет отзывов

Похожие инструкции для Nimbra 300 Series

Бренд: E-T-A Страницы: 6

Бренд: Ableconn Страницы: 16

Бренд: Xantech Страницы: 4

Бренд: I-Tech Страницы: 29

SmartSTACK 100 ELS100-16TX

Бренд: Cabletron Systems Страницы: 16

Бренд: S&S Northern Страницы: 8

Бренд: Black Box Страницы: 3

Бренд: Barksdale Страницы: 6

Бренд: HB Products Страницы: 6

Бренд: Pakedge Device & Software Страницы: 8

Бренд: Black Box Страницы: 2

Chief Kontour KPWR Series

Бренд: LEGRAND Страницы: 8

Бренд: N-Tron Страницы: 17

Бренд: ATTE Страницы: 4

Бренд: Hirschmann Страницы: 8

Бренд: TRENDnet Страницы: 19

MTX-CAT6-2IP-4X16

Бренд: KVMSwitchTech Страницы: 24

Бренд: ORiNG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды