background image

TES-250-M12

Ring

12-48 VDC

V-

V+

Tx+

Rx+

Tx-

Rx-

N.C.

N.C.

N.C.

P1

P2

P3

P4

P5

PWR

Ring

Ring

R.M

Quick Installation Guide

Version 1.4

Q

uick

I

nstallation

G

uide

Introduction

PRINTED  ON  RECYCLED  PAPER

Q I G

ORing's Transporter

series Ethernet switches are designed for industrial

T M

applications, such as rolling stock, vehicle, and railway applications.

TES-

2 5 0 - M 1 2

i s a l i t e - m a n a g e d r e d u n d a n t r i n g E t h e r n e t s w i t c h w i t h

5x10/100Base-T(X) ports which is compliant with EN50155 request. With
completely support of Ethernet redundancy protocol, O-Ring (recovery time <
10ms over 250 units of connection), O-Chain and STP/RSTP (IEEE802.1w/D)
can protect your mission-critical applications from network interruptions or
temporary malfunctions with its fast recovery technologies. It is specifically
designed for the toughest industrial environments.

EN50155

TES-250-M12

Ethernet switch use M12 connectors to ensure tight, robust connections, and
guarantee reliable operation against environmental disturbances, such as
vibration and shock.

can be managed centralized by a powerful

TES-250-M12

windows utility — Open-Vision. In addition, the wide operating temperature
range from -40 C to 70 C can satisfy most of operating environment. The

o

o

TES-250-M12

can be easily adopted in almost all kinds of applications and

provides the most rugged solutions for managing your network. Therefore,
the switch is one of the most reliable choices for rolling stock and highly-
managed Ethernet application.

Package Contents

Installation

Wall-mount

The device can be fixed to the wall. Follow the steps below to install the device on the wall.

Step 1:

Hold  the

evice  upright  against  the  wall

d

Step 2:

Insert  four  screws  through  the  large  opening  of  the  keyhole-shaped  apertures  at  the

top  and  bottom  of  the  unit and fasten the screw to the wall with a screwdriver.

Step 3:

Slide  the

evice  downwards  and  tighten  the  four  screws  for  added  stability.

d

The device is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.

Preparation

Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.

Elevated Operating Ambient:

If installed in a closed  environment, make sure

the  operating  ambient  temperature  is  compatible  with  the  maximum
ambient  temperature (Tma) specified  by  the  manufacturer.

Reduced Air Flow:

Make sure the amount of air flow required for safe operation

of the equipment is not compromised  during  installation.

Mechanical Loading:

Make sure the mounting of the equipment  is  not  in  a

hazardous condition due to uneven mechanical loading.

Circuit Overloading:

Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used  when addressing
this concern.

Safety & Warnings

For pin assignments of power, console and relay output ports, please refer to the following tables.

Contents

TES-250-M12

Pictures

Number

1

QIG

1

Panel Layouts

Front View

1. Fast Ethernet port
2. LNK/ACT LED for Ethernet ports
3. Ring status LED
4. Power status LED
5. R.M. status LED
6. Power port

Wiring

Grounding

Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.

Power port pinouts

The switch provides one set of power supply on a M12 5-pin female A-
coding connector. Insert the power cable to the power connector
on the device and rotate the outer ring of the cable connector
until  a  snug fit is achieved. Make sure the  connection  is tight.

Network Connection

The switch has five 10/100Base-T(X) Ethernet ports in the form of M12 connector. Depending
on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network devices (PCs,
servers, switches, routers, or hubs). Please refer to the following table for cable specifications.

1907-200-S250M12XX1-FX014

S w i tc h

E N 5 0 1 5 5

I N D U S T R I A L

1

3

6

5

Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.

Pin Definition

#1

#2

#3

#4

Configurations

After installing the switch and connecting cables, start the

evice by turning on

d

power. The green power LED should turn on. Please refer to the following tablet
for LED indication.

V-

V+

N.C.

N.C.

N.C.

10/100Base-T(X) D-coding M12 port

Pin No.

Description

#1

TX+

#2

RX+

#3

TX-

#4

RX-

2

4

Cable

Type

Max. Length

Connector

10BASE-T

Cat. 3, 4, 5 100-ohm

UTP 100 m (328 ft)

M12 D-coding connector

100BASE-TX

Cat. 5 100-ohm UTP

UTP 100 m (328 ft)

M12 D-coding connector

LED

Color

Status

Description

Power

Green

On

Power is on

R.M

Green

On

Device operating in Ring Master mode

Ring

Green

On

O-Ring enabled

Blinking

O-Ring structure is broken

10/100Base-T(X) M12 ports

LNK/ACT

Green

On

Port is linked

Off

Port is linked-down

Blinking

Transmitting data

7

.5

0

1

5

0

.6

44.4

73.9

TES-250-M12

Ring

12-48 VDC

V-

V+

Tx+

Rx+

Tx-

Rx-

N.C.

N.C.

N.C.

P1

P2

P3

P4

P5

PWR

Ring

Ring

R.M

1

7

8

.2

40.0

1

4

2

.2

88.9

Ø5.0

Ø8.0

Ø4.0

Dimension

Unit =mm (Tolerance ±0.5mm)

TES-250-M12

EN50155 5-port lite-managed

Ethernet switch

TES-250-M12

1

1. Reset button

TES-250-M12

Отзывы: